Shelly box inline and wago 221 connectors (1Plus, 1L, 2PM, 2.5, Dimmer2)
We calculate the final price from your selected file. You review and accept it before payment.
Preliminary estimate for PETG
€3.55 – €4.34 net (excluding VAT)
For file: shelly_enc_inline_box_v2_0.4n_0.2mm_PETG_MK4IS_3h35m.bgcode
This is an estimate for one file. You’ll confirm the exact price before ordering.
File and estimate settings
File used for this estimate
Average indicative estimate: €3.95 excluding VAT (range midpoint).
- Weight reported by the author
- 61 g
- Print time reported by the author
- 3.59 hr
- Source material
- PET
- Estimate material
- PETG
- Estimate printer
- Bambu Lab P1S - 0.4 nozzle
- Estimate process
- 0.20mm Standard
Indicative estimate for the selected file only, based on the author’s weight and print time. File variants are not added together. The final price is calculated after file analysis.
Saved on this device.
Enclosure designed to hold a Shelly with flex wires in line and wago 221 connectors.
- Rating
- 5 / 5
- Likes
- 215
- Downloads
- 1,531
- Makes
- 11
- Views
- 10,836
- Reviews
- 9
Updated at source:
Model information
- Source
- Printables
- Category
- Electronics
- License
- Creative Commons — Attribution
Part of my series of enclosures designed for Shelly smart devices and Wago 221 connectors.
- Shelly box for T&E 3x slots and wago 221 connectors
- Shelly box for inline flex wire and Wago 221 connectors (this one)
- Shelly box for 2x flex wires and wago 221 connectors
- Shelly box for 3x flex wires and wago 221 connectors
- Shelly quad box for 2x devices/5x relays/5x flex wires and wago 221 connectors
Shelly box for inline flex wire and Wago 221 connectors
This is an enclosure that I designed to hold a Shelly device associated wiring in a closed, electrically safe box. Wiring layout was planned so that the box sat inline between socket and appliance being controlled.
Electrical safety
- Mains electricity carries danger of death. Please don't attempt to use one of these with real circuits unless you are competent and aware of health and safety procedures.
- Use PETG or other fire resistant materials other than PLA.
Purpose and features
The box was designed to hold a Shelly Plus1 to control an appliance. It was fitted in line with a flex wire with a socket plug at one end and an IEC female plug at the other.
Shelly device support: Shelly Plus1, Shelly 1L, Shelly 2.5, Shelly 2PM, Shelly Dimmer2
Wire strain relief: Each twin&earth entry port has slots for fitting a cable tie as strain relief for the wires.
Attachment holes: The box has counter-sunk holes to attach it to a surface.
Cooling slots: There are cooling slots all around and above/below the shelly device.
Lid fitting: The lid attaches to the box using 4x M3 screws (5-10mm max) which thread into M3 heat inserts to be installed on the box.
Printing notes
- The lid requires supports on the bolt hole counter-bores, otherwise it will not print cleanly (in my case it didn't)
Version control
Version 2.1 - 11/03/2024
- Updated (reduced) cable tie shelf width, validated lid locator and wago pad locations
Version 2.0 was a significant redesign to include the following features:
- M3 heat thread inserts instead of square nut slots or holes for tapping
- Attachment bolt holes on the inside of the box rather than outside brackets
- Cable tie pads inside the box as opposed to accessible from the outside (enables refitting ties without dismounting the box)
- Shelly slot adjusted for compatibility with multiple models