1 / 4
Ikea 365+ storage box with manual filament rewinder for 2 spools — zdjęcie 1
1 / 4

Ikea 365+ storage box with manual filament rewinder for 2 spools

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A 2 spool filament storage dry box with a magnetic manual rewinding system to retract filament when not in use.

Ocena
0 / 5
Polubienia
5
Pobrania
25
Wydruki
0
Wyświetlenia
552
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution

I print with one filament at a time, but occasionally change filaments to print a different colour/material, so I wanted to find a way to push the filament back into a dry box without it slipping off the spool and causing tangles. I live in Singapore where the humidity is always 80%+ so leaving the filament exposed is not an option, even for PLA. 

I have tried filament buffers including the Voron ERCF, but the y are cumbersome to assemble, bulky and cause a lot of friction along the filament path. 

Inspired by the magnetic rewinding system designed by Brickman93 (linked here), I designed from scratch a 2-spool holder with magnetic rewinder for the Ikea 365+ food container (inverted) as I already had several of these at home and did not want to buy new containers.

The holder can fit spools up to 75mm wide, although depending on the diameter it may touch the top of the box due to the slanted walls. Prusament spools fit nicely in this box. 

All the parts are printed from Prusament ASA as that was what I had on hand, but PETG and even PLA should be fine too.

I have used N52-grade neodymium magnets, anything less and the rewinder may not work completely. As it is, the knob needs to be turned slowly to avoid slipping especially if you have a long bowden tube like in a Voron printer. 

To rewind the filament, you will need to open one of the clips to place the handle, this should not affect the seal of the container as the other 5 clips remain closed. 

Here's what you will need: 

  1. 8pcs 608 ball bearings (8x22x7mm, shielded or unshielded doesn't matter)
  2. 8pcs 8mm diameter x6mm cylinder magnets (N52), you can also use 8x3mm magnets (16pcs needed)
  3. 4pcs 8mm diameter x8mm cylinder magnets (N52 grade), for the handle.
  4. Friction tape - minimum 10mm wide. I am using a rough tape that I bought from Misumi, but silicone may work as well. 
  5. (printed part) 1x Base
  6. (printed part) 4x Roller
  7. (printed part) 4x Shaft
  8. (printed part) 4x Shaft_magnet_holder
  9. (printed part) 1x Handle_magnetic

To assemble, first put the friction tape on the ends of only 2 of the 4 rollers, the other 2 rollers don't need the tape. 

Also glue 4 magnets into each of 2 magnet holders. The other 2 magnet holders don't need magnets.

Then, glue the 4 8x8mm magnets into the handle, making sure that they are oriented correctly to attract those on the spool magnet holders when the magnets directly face each other (ie. no printed parts between them). 

Next, place 4 bearings on the centre divider of the base, and hold them in place to insert the 4 rollers (you will need to flex the outer wall of the base slightly to get them in). Each side will have one roller with the friction tape, and one without. The end of the roller with the design is facing the centre. 

Next, glue the magnet holders flush with the end of the shafts with the magnets facing outwards. 

Insert the other 4 bearings into the holes in the base outer walls, and slide the shaft+magnet holder all the way into the bearing and roller. The shaft with the magnets should go with the roller with the friction tape. 

Here's the assembled spool holder:

Once the spool holder is inside the dry box, position and drill the holes for the filament to feed through. I used PC4-M6 fittings connected to Bowden tubes, and have included the files for a simple 3d-printed fitting for the PC4-M6 to screw into inside the container. 

Tagi