1 / 11
Automated Air Filtration System for Cat Litter Boxes - Universal Fit - Customizable — zdjęcie 1
1 / 11

Automated Air Filtration System for Cat Litter Boxes - Universal Fit - Customizable

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Universal cat litter air filtration system with Arduino, sensor-triggered fan, safety features, customizable.

Ocena
5 / 5
Polubienia
65
Pobrania
147
Wydruki
0
Wyświetlenia
1491
Oceny
1

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Pets
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Automated Air Filtration System for Cat Litter Boxes - Universal Fit - Customizable

This is a universal, Arduino-powered air filtration system designed to be mounted on virtually any cat litter box. The goal of the project is simple: automatically remove odors after your cat uses the litter, all while ensuring maximum safety and minimal disturbance.

At its core, the system is powered by an Arduino UNO and a VL6180X proximity sensor. When your cat enters the litter box, the sensor detects its presence and activates an orange LED to indicate the box is in use. Once your cat exits, the system waits 15 seconds for safety, then activates a 12V fan via a 5V relay, extracting air for 2.5 minutes. If the cat returns during this time, the fan immediately shuts off, and the cycle restarts once the litter is vacated again.


The waiting and extracting times can be customized in the Arduino code


The electronics are built on a perfboard, with all component connections manually soldered. Power is supplied through a 12V PSU connected directly to the Arduino, but it also supports 12V battery power. When running on battery, the corresponding code includes a voltage monitoring system: if the battery drops below a safe threshold, the system automatically shuts down to prevent over-discharge and the orange LED flashes three times quickly to indicate that the battery needs to be recharged.

 

🌬 PWM Fan Control – A Challenge

During early development, I attempted to use PWM (Pulse Width Modulation) to smoothly ramp up the fan speed, hoping to avoid startling the cat. However, with my Noctua 12V fan, even using the manufacturer-recommended PWM frequency, the fan would never fully turn off it always stayed at minimum speed. For this reason, I switched to relay control, but if anyone has tips for making PWM work reliably with Noctua fans and Arduino UNO, I’d love your input!

 

🌫 Filter Compatibility

The filter housing is designed to fit Zortrax HEPA + Carbon filters, which I already had available. If you’re using different filters, feel free to remix the filter case to match your specific dimensions.

 

PROGRAM SETUP - ARDUINO IDE                                                            

#include <Wire.h>
#include <Adafruit_VL6180X.h>

const int fanRelay = 8; // Relay pin to turn fan ON/OFF const int ledRed = 10; // Red LED (blinking when fan is ON) const int ledGreen = 11; // Green LED (litter available)

const int minDistance = 200; // Detection threshold for cat presence(mm) const int waitTime = 15000; // Safety Waiting Time after cat exit (ms) const int fanRunTime = 150000; // Air Extraction Time (ms)

Adafruit_VL6180X vl6180x = Adafruit_VL6180X(); // Create a sensor object

// State variables bool isCatInside = false; // True if a cat is currently detected bool isWaitingExit = false; // True if waiting to confirm cat has left unsigned long exitTimerStart = 0; // Time when exit wait started

// Initialization function void setup() { // Set up pins pinMode(fanRelay, OUTPUT); pinMode(ledRed, OUTPUT); pinMode(ledGreen, OUTPUT); digitalWrite(fanRelay, LOW); // Ensure fan is OFF initially

// Start serial communication
Serial.begin(115200);
if (!vl6180x.begin()) {
    Serial.println("Failed to detect VL6180X sensor!");
    while (1);  // Stop if sensor is not found
}

// Initial LED status: green ON (litter available), red OFF digitalWrite(ledRed, LOW); digitalWrite(ledGreen, HIGH); }

// Main loop function void loop() { int distance = vl6180x.readRange(); // Read current distance from sensor

// If a cat is detected (closer than threshold)
if (distance &lt; minDistance) {
    if (!isCatInside) {
        isCatInside = true; // Update state
        Serial.println("Cat is inside the litter box");
        digitalWrite(ledRed, HIGH); // Turn on red LED
        digitalWrite(ledGreen, LOW);// Turn off green LED
        isWaitingExit = false;     // Reset exit check
    }
} else {
// If cat was inside and is now possibly gone, start exit confirmation
    if (isCatInside &amp;&amp; !isWaitingExit) {
        Serial.println("Waiting to confirm cat exit...");
        isWaitingExit = true;
        exitTimerStart = millis();// Start timer
    }

// If in exit waiting state if (isWaitingExit) { unsigned long currentMillis = millis(); // Monitor distance for the full wait time while (millis() - exitTimerStart < waitTime) { distance = vl6180x.readRange(); // If cat comes back during wait, abort exit if (distance < minDistance) { Serial.println("Cat is still inside"); isCatInside = true; isWaitingExit = false; digitalWrite(ledRed, HIGH); digitalWrite(ledGreen, LOW); return; } delay(500); // Check every 500ms } // Exit confirmed: turn OFF red LED, turn ON green LED Serial.println("Cat has exited"); isCatInside = false; isWaitingExit = false; digitalWrite(ledRed, LOW); digitalWrite(ledGreen, HIGH);

 // Start fan and blinking red LED
        Serial.println("Starting air filtering...");
        digitalWrite(fanRelay, HIGH); // Turn fan ON

        unsigned long fanStartTime = millis();
        bool ledState = false;
        unsigned long lastBlink = millis();

// Fan will run for a fixed duration unless interrupted while (millis() - fanStartTime < fanRunTime) { // If cat returns, immediately stop fan if (vl6180x.readRange() < minDistance) { Serial.println("Cat detected again, turning OFF fan..."); digitalWrite(fanRelay, LOW); digitalWrite(ledRed, HIGH); isCatInside = true; digitalWrite(ledGreen, LOW); return; }

            // Blink red LED every 500ms
            if (millis() - lastBlink &gt;= 500) {
                ledState = !ledState;
                digitalWrite(ledRed, ledState);
                lastBlink = millis();
            }

            delay(10); // Small delay for responsiveness
        }

   // Fan time completed, turn OFF fan and red LED
        Serial.println("Stopping fan...");
        digitalWrite(fanRelay, LOW);
        digitalWrite(ledRed, LOW);
    }
}

delay(500); // Wait before next sensor check

}

To change the waiting and fan operation time you can easily change the value in millisecond of const unsigned long waitTime and const unsigned long fanRunTime in the first potion of the code.

This is the code for power supply operation, but in the download section, you can also find the one for battery use.

⚠ Note: The code for battery use requires an additional part in the circuit to read the voltage. This version, with battery monitoring implemented, can be used both with a battery or a power supply.


➡ More Schematic info in the Downloads section > Assembly Instruction!

 

🛠 Project Development with  PCBWay’s Support

A massive thank you to PCBWay for helping bring this project to life.

PCBWay specializes in PCB, PCBA, CNC, and 3D Printing, and has (in my experience) the best support & the widest amount of options for manufacturing. 

 

They also have a PCBWay+ Store where I purchased everything needed for this project, including the VL6180X proximity sensor, Jumper Wires for prototyping, and a Multimeter to test circuit connections. You’ll also find the Relay Module compatible with Arduino. 

In addition to the essential components for this build, range of electronic parts and accessories at great prices, with an easy checkout process and fast, well-packaged shipping. 
Check out this project on PCBWay+ Community.

 

🔧 Print Settings

Layer Height: 0.2mm

Infill: 30–50%

Perimeters: 2–3

Supports: Not required

Material: PLA or PETG recommended

 

🖨 Print Files & Quantities

1× Electronics Case

1× Electronics Case Lid

1× LED Diffuser (in transparent material)

1× Sensor Case (Bottom)

1× Sensor Case (Top)

1× Fan Mount & Filter Case

1× Filter Housing (Zortrax compatible)

1× Filter Safety Clip

 

🔩 Hardware Required

1× Arduino UNO

1× VL6180X sensor

1× 12V 120mm fan

1× 5V relay module (or compatible MOSFET switch)

⚠ Note: I used a basic relay controlled directly from a digital pin, but I highly recommend using a dedicated relay module to protect your Arduino from excessive current draw.

1× 3mm Green LED

1× 3mm Orange/Red LED

2× 220Ω Resistors

1× 12KΩ Resistor (optional)

1× 4.7KΩ Resistor (optional)

1× 4-pin JST XH Board Connector Set (or similar)

1× 4-pin Header Strip

1× 1-pin Header Strip

1× Perfboard (up to 6,9 x 4,5 cm)

1× 12V 1A DC Power Adapter

1× 12V Battery (optional)

1× Zortrax Hepa + Carbon Filter SET

1× Digital Multimeter

Screws and Zip Tie (type and quantity inside BOM)

22AWG Solid Core Wire for circuit wiring and connections to Arduino ports

A full Bill of Materials (BOM) and a step-by-step assembly guide are available in the Downloads section.


📁 Software Used

Arduino IDE

Fusion360
 

🖥 Serial Monitoring for Smart Integrations

The Arduino code includes serial messages to indicate the system’s current state. This opens the door for remote monitoring, integration with smart dashboards, or logging battery performance over time, great for further development!

 

💡Expansions and Integrations

If your litter box is very large and you’re concerned that the cat might not be properly detected by the sensor, you can modify the project by adding one or more additional sensors to achieve full coverage inside the box. Alternatively, you can increase the waiting time as needed, to give your cat enough time to do its business even if it’s in a spot not covered by the sensor.

 

🔁 Share Your Make & Remix!

I’d love to see how you build and customize this project. Your feedback is incredibly valuable and helps me improve my designs.

If you create improvements, remixes, or alternate modules, share them with the community!

 

🐾 Follow for More

Don’t forget to follow 3D KIMBA for more projects, creative ideas, and helpful tools for makers!

 

Tagi