Magnetic Charge parts for XR Vesc platforms
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
It's 2025, XLR charge parts need to go. This is a complete DIY charging setup that attaches via magnets and pogo pins.
- Ocena
- 0 / 5
- Polubienia
- 2
- Pobrania
- 5
- Wydruki
- 0
- Wyświetlenia
- 161
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Electronics
- Licencja
- Creative Commons — Attribution — Noncommercial
Having a magnetically attached charge port for your XR based VESC isn’t a requirement by any means, but it is a quality of life improvement that is amazing. This is meant to be able to replace the standard XLR charge port. It is not designed to fit the GT, Pint or any other sized charge connector. This is also only a 2-wire connection: Positive and negative.
There are 5 separate parts to print out:
- Charge side - the part that connects to your charger
- Battery side - the part that connects to your battery
- Gasket - sits between the Battery side piece and your enclosure
- Nut - secures the Battery side piece to your enclosure
- Battery side cover - put this on your charge port when you’re riding to protect agains dirt and debris.
***IMPORTANT*** This charging setup has not been tested with fast charging currents. I’ve only used it with standard charging currents: 4 amps. Anything higher is use at your own risk
***IMPORTANT*** This charging setup has not been tested with batteries over 84V. Although the parts are rated at up to 100 VRMS/150 VDC, use at your own risk.
***IMPORTANT*** This setup does NOTHING to prevent your charge port from being “hot”. If you don't already have a BMS that manages this, or diodes setup to prevent this, do NOT use this.
BILL OF GOODS
Here are all the parts you’ll need for this project:
- 6 2.5x2.5x7 magnets. I get mine from First4magnets.com link
- 2 pre-wired, spring-loaded connectors, part # 867-22-002-70-501010. Digikey link
- 2 pre-wired target pad connectors, part # 867-10-002-70-502010. Digikey link
- TPU for the charge side connector
- PETG or whatever for the battery side (use whatever you want, but it should have a high temp rating)
- Superglue plastics bonder. This is the stuff that has both an activator and glue. It might not be 100% necessary, but I found it helpful to keep the charge side connectors in place when putting the silicone glue in place
- Silicone glue
- Some small tools to push the silicone glue down into the crevasses of the battery and charge side pieces.
- Some heat shrink for the charge side connectors.
- Whatever connectors you use for your vesc to connect to the battery (XT30?) and charger (XT60?)
- Whatever wire sleeving you want to use to keep all the wires manageable.
- Alcohol wipes or shop paper towels and rubbing alcohol
- Some method to prevent your charge port from being “hot” when not charging.
BATTERY SIDE
I printed the battery side in PETG, although other filaments that can resist high temps are usable. I tried printing this in TPU and PAHT-CF, but the threads never came out good. The settings I used with PETG are:
- 3 walls
- .16 layer height, .2 first layer
- Line width: .6, Outer wall: .6, Inner wall: .6, all others default
- Precise wall: checked
- Print Infill first: checked
- Paint the seams vertically on one of the flat walls. Makes cleanup way easier, and the nut fit way better.
- Bridge flow and Internal Bridge flow: 1.1
- Update your Bridge Infill Direction so the bridges over the magnet hole are across the width of the hole, not the length.
- Painted tree supports. The overhang for the top rim is the only place painted.
- Support Top Z Distance: .22
- There is a pause at the layer where the magnets are covered with filament to insert the magnet, no glue necessary.
GASKET
This is printed in TPU. Nothing special here.
NUT
This is PETG. The only settings I used were .16 layer height, .2 first layer.
CHARGE SIDE
Print this in TPU. I used Bambulabs 95A. The settings I used are:
- .16 layer height, .2 first layer
- 3 walls
- Update your Bridge Infill Direction so the bridges over the magnet hole are across the width of the hole, not the length.
- Wall generator: Arachne
- There’s a pause at the layer where the magnets are covered with filament to insert the magnet, no glue necessary.
- I added a cube modifier to the base of the print sized approx: 15.3 (X), 19.3 (Y), 11.9 (Z). For the modifier, add fuzzy skin to the contours
CAP
Print this in TPU also, the same exact settings as the Charge side piece, minus the modifier and fuzzy skin.
*** SAFETY FEATURES***
This assembly is meant to be able to be reversible, meaning you can attach them in whatever orientation you want. In order to allow that to happen and not blow up your battery, there are 2 safety features, one built in and one during assembly that you have to pay attention to.
The built in safety feature are the sloping sides on the top of the battery battery side connector. This will prevent you from connecting a positive wire to a negative by forcing the charge side to rotate into the correct orientation. See the attached cross section screenshot.

The other feature is the way the holes for the 2 sets of wire connectors are laid out. Put the same polarity of wire on the outside, and the opposite on the inside. For example, if the outside wires are always positive, then they will never be able to connect to the negative, but they will always connect to the positive, regardless of orientation of the printed part. YOU HAVE TO PAY ATTENTION TO THIS DURING ASSEMBLY!!!! See the attached image:

A third safety feature is how recessed the charge side pins are in relation to the top of the part. This makes it a little more difficult to actually touch the pins, or have them accidentally touched by anyone or anything. However, you, as the user, are responsible for using common sense here.
ASSEMBLY PART 1: TEST FITTING AND PREP
Once you have the Charge side, Battery side and Cap printed, check to make sure you have your magnets aligned correctly. The Battery side and Cap should connect perfectly, no gaps. The Battery side and Charge side should connect perfectly, no gaps. If there are for either, either reprint or do whatever cleanup you need to do. More than likely, the TPU stuff needs a little cleanup.
See this image for a BAD fitting, noticing how Charge side (gray part) is at an angle:

Here's how it should look:

Next, make sure the Nut screws on to the Battery side cleanly.
Next, add the target pad connectors to the battery side part. Make sure you get your alignment right: + wires on the outside and negative on the inside. The tops of the pads should fit flush with the opening they go in. Not recessed, not protruding. *Flush*.

Next add the spring pin connectors into the chart side part. Keep your alignment of the wires identical to what you did for the battery side part. Push the pin connectors as far in as they’ll go. There’s a little lip on the TPU part that should prevent them from going too far.

Connect your battery side and charge side parts. The parts should connect evenly, snug and *level*. You should also be able to jiggle the 2 connected pieces without them coming apart at all. If any of this is not true, STOP. Readjust and/or reprint your parts as necessary. Please see the above images for how the fit should look.
***IMPORTANT***
It’s important that the 2 pieces fit together securely and perfectly level. We don’t want all the current to be carried by a single wire. These are 24g wires and shouldn’t be able to deal with the current’s that will be used.
It’s probably a good idea to use a multimeter to validate continuity. If you’ve made it this far and everything is good, you’re ready to glue all the bits together.
Cut and prep some of your wire sleeve to the length you want it to be.
ASSEMBLY PART 2: ELECTRIC BOOGLUE
BATTERY SIDE
The main purpose of the superglue is to hold the pad connectors in place so that when we’re adding the silicone glue later, the pads don’t become disconnected from the 3d printed part. The glue shouldn’t be considered “structural”.
Assuming you used PETG, you’ll need the 2 part superglue (activator and glue). For the activator, depending on what product you bought, you might need to trim the application tip to fit in the holes that the pad connectors are put in. Either way, put activator on the inside walls of those holes. Cover as much of the walls as possible. Put activator on the plastic part of the pad connectors as well.
Insert the pad connectors into the Battery side part. **PAY ATTENTION TO THE POLARITY**. Leave the actual pad connectors about an inch from being inserted all the way. Next, put a small amount of superglue on the *inside* walls of the Battery side part where the pad connectors will be inserted. Be careful to not get glue on the pads or wires. You probably should be wearing gloves or something, too.
Once the glue is applied, push the pad connectors all the way in, again PAY ATTENTION TO THE POLARITY OF THE WIRES!!! Make sure the pads are flush with the insertion point. Clean up any glue residue that might have escaped with the alcohol wipes.
Set this part aside to dry/cure.
CHARGE SIDE
We’re not using super glue for this part. The method to keep the pin connectors in place while we add the silicone glue will be the heat shrink tubing. Cut 4 pieces of tubing to about 10mm in length. Add them to each of the wires so that the tubing covers the bottom 1/3 of the metal jacket of the wires. Heat shrink them on, being careful not to melt the existing covering of the wire. The heat sink should adhere good enough to the silicone glue. 

Push the pin connectors all the way in to the TPU part. Double check the connection with the Battery side part: Level, secure and continuity. Start adding some silicone glue, only a little at a time. Use whatever tools you have to push the silicone glue down into all the crevasses of the cavity. Once the cavity is about 1/2 full, push the wire sleeve on your wires, all the way into the cavity. I’ve found that adding masking tape to the free end of the wires helps get the wires through the sleeve.

Once the sleeve is in place, make sure the top of the pin connectors are still in their hole. Reseat if necessary. Finish filling up the cavity with silicone glue.

BATTERY SIDE PART 2
Once the superglue is set, repeat the steps for the Charge side part with the silicone glue.

Once all the silicone glue is cured, do another test fitting!! Make sure both parts (Battery and Charge) fit secure and level. Double check continuity! ALL 4 wires!! Each wire should only have connectivity with one other wire. i.e. Each negative should have continuity to only one other negative. But it should have continuity. If there's continuity with more than one wire, stop and redo everything.
If all your safety checks pass, you can start soldering your wires and other connectors. On each piece, solder the 2 positive wires together, and the 2 negative wires together. Check continuity.
EVERYTHING BELOW THIS IS AN EXERCISE FOR YOU, AND YOUR RESPONSIBILITY.
You should know what you’re doing for everything after this. There won’t be a walk-through, step-by-step, or hand holding. If you don’t know how to solder, or check your work with a multimeter and/or other tools, GET A PROFESSIONAL TO HELP YOU. THE BELOW ARE JUST SUGGESTIONS!
Solder your XT30 and XT60 (or whatever you use) together. Check continuity.
Connect your Charge side to your charger. Add the battery side. Check continuity, voltage and amps. Double check your work. Then check it again. Disconnect all the pieces. Connect your Battery side MagSafe part to your batteries connector. Connect your Charge side MagSafe part to the charger. Connect your MagSafe parts. Verify amperage, voltage, and everything else.
Once you’re satisfied with the safety of your new connections, put it all together. Make sure the Nut fits securely and holds the Battery side part in place. Make sure the cap still connects securely. Charge your board and go ride.