1 / 3
Menlu 8mm to 32mm Strip Feeder + Magazines + Discard Bin for LumenPnP — zdjęcie 1
1 / 3

Menlu 8mm to 32mm Strip Feeder + Magazines + Discard Bin for LumenPnP

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Added 16mm, 24mm, & 32mm Menlu Strip Feeders. Updated all feeders to work with EIC-481-C standard max component heights.

Ocena
0 / 5
Polubienia
4
Pobrania
111
Wydruki
0
Wyświetlenia
565
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution

CHANGES FROM ORIGINAL:

  1. Added 16mm, 24mm, & 32mm Menlu Strip Feeders. 
  2. Updated all feeders to work with EIC-481-C standard max component heights. 
  3. STEP FILE instead of STL
  4. Update 8/4/2025:
    • Added top camera compatible Menlu-EH (extra high & equal height) feeders, for use with underside mounted staging plates.
    • Adding reduced height staging plate foot.
    • Added 8mm to 32mm cut tape magazines. 
    • Added 16x universal carrier, with improved countersinks to prevent screw heads from sticking up too high.
    • Updated 8mm top slider for easier assembly with o-ring. Still recommend a good pair of tweezers though. 
  5. Update 8/5/2025: 
    • Reduced component magazine female stud height 1mm in the event the cover warps slightly, it will still close all the way.
  6. Update 8/9/2025
    • Added Menlu style discard bin, corrected SLDPRT files to STEP.Added Menlu style discard bin, corrected SLDPRT files to STEP.
  7. Update 8/30/2025

Everything in here should get you up and running 8mm to 32mm Menlu feeders, with magazines, and top camera compatibility. 

 

PRINTING NOTES:

Polymaker PLA PRO was used. For the wider feeders, your bridging settings need to be dialed in. This is what worked for me: 1 perimeter for the bridging layer of the top slider & bottom guide rail. The layer after the bridged layer, print the whole layer the same speed as you do your bridges (I used ~20mm/s) Also recommend 0.2mm layer height for bridge layers + layer after bridge. Doing this I didn't need supports.

Additionally, make sure elephant foot compensation is correctly tuned to your printer, otherwise the slider may be a tad tight. 

 

LumenPnP TOP CAMERA FOCUS NOTES:

Due to 12mm through 32mm being taller than the original Menlu, parts may or may not be in focus for the top camera of the LumenPnP, so part pick location may need to be set by manually jogging nozzle to part instead of with the help of the top camera. 

***UPDATE 8/4/2025: The top camera focus problem has been fixed by mounting the staging plate to the underside of the 2020 aluminum extrusion, and printing the reduced height staging plate foot in addition to the Menlu-EH (extra high & equal height) bottom guide rails. These bottom guide rails are compatible with the top sliders, peel clips & universal carrier which you may already have. 

***WARNING: Make sure to slide the top slider to the rear (pushing against the spring force), to provide clearance to mount the Menlu-EH feeders to the universal carrier, if configured in the aforementioned manner. Also, do not use Menlu-EH feeders on normally (top) mounted staging plates, or you may crash the head into it. 

 

8 TO 32mm MENLU CUT TAPE MAGAZINE:

Will not work with photon feeder rail installed, so removal is necessary, and if using 3x staging plates, it's a tight fit, but you can make it work by:

  1. Sliding front two staging plates as far forward as possible without interfering with photon feeders.
  2. Remove rear photon feeder PCB rail.
  3. Slide rear extrusion previously used for the photon feeders as far back as possible. To get it far enough back, you also need to remove the rear most 2020 extrusion 90 degree brackets.
  4. Et voilà, you have room in the rear for the 3rd staging plate to mount the Menlu-EH feeders to and use in conjunction with the 8 to 32mm Menlu Cut Tape Holders.

Magazine remix from original: https://www.printables.com/model/966194-menlu-8mm12mm-cut-tape-holder-for-lumenpnp 

 

PARTS LIST:

Indexing Pin: 1.5mm dia x 6mm length

Spring (replaced w/ o-ring): 16mm OD x 1.5mm Thick O-ring

 

ORIGINAL:

Please see original for printing instructions & more info: https://www.printables.com/model/885928-menlu-strip-feeder-8mm12mm-for-lumenpnp 

Tagi