Servo and drive motor mechatronic connectors
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Dowel and Lego compatible connectors for Raspberry Pi controlled servo and drive motor driven mechatronic constructs
- Ocena
- 0 / 5
- Polubienia
- 17
- Pobrania
- 58
- Wydruki
- 0
- Wyświetlenia
- 838
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- RC & Robotics
- Licencja
- Creative Commons — Attribution — Noncommercial
A set of printed components to build frameworks that incorporate servo and drive motors to build mechatronic / animatronic structures controlled by a Raspberry Pi.
Other related 3D print designs are here and here.
Detailed descriptions of all aspects of this evolving project are at this link and example ‘mechatronic’ software for a Raspberry Pi can be downloaded from here.
The various 3D prints developed for this project allow servo motors to be connected to 3.8mm (5/32 inch) diameter wooden dowels which, along with other dowel interconnects plus screw-down or Lego compatible stands, allow 2D/3D frameworks to be built.
Simple 2D animatronics can be built, as shown in the images, using cardboard cut-outs attached to the stand.
All the 3D print components use 1.75mm PLA and a layer height of 0.15mm with print details for each component produced on an i3 Mk3 shown in the table below.
component file name/description | needs support (Y/N) | brim (mm) | filament | print time |
3x_servo_connected_case05_repaired.stl - servo motor holder with 4 dowel spigots | Y | 3 | 6.45 | 2h 47m |
9x_corner_connector01.stl - dowel only corner connectors | N | 3 | 4.02 | 2h 8m |
9x_cross_connector01.stl - dowel only cross connectors | N | 3 | 5.16 | 2h 25m |
12x_t-connector01.stl - dowel only T connectors | N | 3 | 5.49 | 2h 35m |
12x_right-angle_connector02.stl - dowel only right-angled connectors | N | 3 | 4.05 | 1h 57m |
LEGO_4x2_brick_corner_connector01.stl - LEGO compatible brick with dowel spigots | Y | 5 | 1.49 | 47m |
DUPLO_2x3_brick_corner_connector01.stl - DUPLO compatible brick with dowel spigots | Y | 5 | 4.84 | 2h 1m |
8x_simple_arm07.stl - 1pc servo arms with spigot allows smaller/lighter items to be attached to a servo | N | 4 | 4.63 | 1h 55m |
simple_disc04_servo_side+object_side.stl - 2pc servo arm with spigot allows large mechatronic items to be attached to a servo | N | 3 | 1.1 | 29m |
9x_fixing_1mm_washer01.stl - fixing washers used as spacers between a connected object and its servo arm | N | 3 | 0.38 | 11m |
stand_up_x3_strip_tilted+image_holder01_rot9.4.stl - screwed-down stand/image holder with 3 spigots | N | 5 | 2.73 | 1h 7m |
stand_up_x6_strip_tilted+image_holder04_rot9.4.stl - screwed-down stand/image holder with 6 spigots | N | 5 | 4.42 | 1h 51m |
stand_up_x3_strip_LEGO_2x11_tile.stl - LEGO compatible stand/image holder with 3 spigots | N | 5 | 3.3 | 1h 16m |
stand_up_x6_strip_LEGO_2x18_tile01.stl - LEGO compatible stand/image holder with 6 spigots | N | 5 | 5.57 | 2h 9m |
slotted_card_holder01.stl - stand-alone 4 slot card holder | N | 3 | 1.53 | 38m |
slotted_6x_card_holder01.stl - stand-alone 7 slot card holder | N | 3 | 2.68 | 1h 6m |
|
|
|
|
|