1 / 6
BMW R1200 GS slider for crash bars (with hook) — zdjęcie 1
1 / 6

BMW R1200 GS slider for crash bars (with hook)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

This 3D model was specially designed for BMW R1200 GS up to 2012 crashbars manufactured by “Armor Bike”. I do not know…

Ocena
0 / 5
Polubienia
1
Pobrania
11
Wydruki
0
Wyświetlenia
246
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Automotive
Licencja
Creative Commons — Attribution — Noncommercial — NoDerivatives

This 3D model was specially designed for BMW R1200 GS up to 2012 crashbars manufactured by “Armor Bike”. I do not know if this slider will fit any other crashbars. As it turned out, the mounting holes in the side plate of different crashbars are drilled with a different offset relative to the frame. Therefore, the sliders do not have round mountig holes, but slots. The front bar (with the logo) is different for the right and left sides of the motorcycle (the printbeds are labeled in the profile). The rear plate is used for fastening. It is available in two types - with an additional hook and without it. The hook is convenient for hanging a helmet or some kind of bag on it. However, be careful. When the engine is running, the bag can rest on the exhaust pipe and melt against it. The helmet does not reach the pipe. If you do not need a hook, print a rear plate without a hook. To install two sliders, you will need 8 M3x16mm HEX bolts, 8 M3 self-locking nuts and 4 3x8mm flat-head screws.

Installation procedure:

  1. Take the rear plate and 2 cylindrical spacers. Loosely secure the spacers in the slots using 3x8mm screws. The spacers should freely slide in the slots.
  2. Apply the rear plate to the safety bar so that the spacers fit into the holes on the metal plate of the crashbar.
  3. Take the front plate (with the logo) and apply it to the desired position.
  4. Move the rear plate so that its mounting holes coincide with the holes of the front plate.
  5. Tighten the screws that hold the cylindrical spacers.
  6. Secure the front plate to the rear plate using four M3x16 screws and four M3 self-locking nuts.

💥Check out other GS-labeled sliders and R1200GS headlight protector 3d-models here:

Headlight protector https://www.thingiverse.com/thing:7047735 Slider https://www.thingiverse.com/thing:7041872


Эта 3д-модель была специально спроектирована под дуги производства компании Armor Bike для BMW R1200 GS до 2012 года. Я не знаю, подойдёт ли этот слайдер к каким-либо другим дугам. Как оказалось, крепёжные отверстия в боковой пластине у разных дуг просверлены с разным сдвигом относительно каркаса. Поэтому в сладерах сделаны не круглые отверстия, а слоты. Передняя планка (с логотипом) отличается для правой и левой стороны мотоцикла (в профиле столы подписаны). Для крепления используется задняя прижимная планка. Она есть двух видов - с дополнительным крюком и без него. Крюк удобен, чтобы вешать на него шлем или какой-нибудь пакет. Однако, будьте внимательны. При работающем двигателе пакет может опираться на выхлопную трубу и плавиться об неё. Шлем до трубы не достаёт. Если крюк вам не нужен, распечатайте прижимную планку без крюка.

Для установки двух слайдеров вам понадобится 8 болтов M3x16 мм с внутренним шестигранником, 8 самоконтрящихся гаек M3 и 4 самореза 3х8мм с плоской головкой.

Порядок установки:

  1. Возьмите заднюю прижимную пластину и 2 цилиндрические проставки. Свободно закрепите проставки в слотах при помощи саморезов 3х8мм. Проставки должны скользить в слотах.
  2. Приложите заднюю прижимную пластину к дуге безопасности так, чтобы проставки попали в отверстия на металлической пластине дуги безопасности.
  3. Возьмите переднюю пластину (с логотипом) и приложите её в требуемое положение.
  4. сместите заднюю прижимную пластину так, чтобы её крепёжные отверстия совпали с отверстиями передней пластины.
  5. Затяните саморезы, которые удерживают цилиндрические проставки.
  6. Закрепите переднюю пластину к задней при помощи четырёх винтов М3х16 и четырёх самоконтрящихся гаек М3.

💥Другие слайдеры с маркировкой GS и защита фары R1200GS здесь:

Защита фары https://www.thingiverse.com/thing:7047735 Слайдер https://www.thingiverse.com/thing:7041872


💥 Donations can be made here: https://boosty.to/prosmp/donate

💥All our contact information in one place: https://hipolink.me/prosmp

YouTube channel: https://www.youtube.com/@prosmp Our Telegram channel: https://t.me/prosmp VKontakte group: https://vk.com/pro_smp

Category: Automotive

Tagi