1 / 1
Godox MF12 to 72mm magnetic round-adaptor — zdjęcie 1

Godox MF12 to 72mm magnetic round-adaptor

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Adaptor to use magnetic accessories from a Godox A100/V1/V100 on a Godox MF12

Ocena
0 / 5
Polubienia
3
Pobrania
22
Wydruki
0
Wyświetlenia
128
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Photo & Video
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Godox MF12 to 72mm magnetic round-adaptor (i.E. Godox AD100pro, Godox V1, Godox V100 [not tested])
The image shows the adaptor together with a magnetic diffusor (other project)

As i own quite a couple of lightformers and diffusors for the round Godox AD100pro, i wanted to use them also on my smaller Godox MF12 macro-flashes.
So i started designing this adaptor. It's clamped to the front of the MF12.
The printing (.3mf file) stops at layer 24 to allow you applying a separation layer using a permanentmarker (more information see blow) for better separation of the supporting structure.
It's still a bit tricky to break it off, but you will be rewarded with a much cleaner surface where the magnets of the diffusor unit (other project) will slide smoothly. You can leave this step out, if you accept loosing smootheness, but then you MUST reset the modified values for "Top Z Distance" and "Top Interface Spacing" (Register "Support") to their standard values, otherwise you won't get off the support structure later. 
To ensure the magnetic property of the AD100/V1/V100, there is a second stop at layer 54, so you are enabled to insert a M60x0,5 (=60x75x0,5) iron shim/washer before continuing the print.
This magnetic feature is cucial, otherwise the construction loses its sense. Clean it from any grease before inserting it, so you can glue it later - if necessary at all.
The clamping might be a bit tight, but it will get weaker over time. So be careful not to break the clamps at the beginning. 
You might resize the whole unit by +0.5-1%, if you feel that it is too tight - it will still work. 
Don't resize it to smaller dimensions, otherwise you won't be able to insert the shim/washer!

Here you might get the shim/washer
https://www.ebay.de/itm/166048142695?_skw=Pa%C3%9Fscheibe+M60
If you have another supplier: Don't use stainless steel ones, dependent on the alloy, they might have less or even no magnetic property!

The additional print is used to mask the object when the print stops at layer 24 for applying the parmanentmarker.

Printed on a Bambulab P1S with Sunlu PLA+ 2.0

Thanks a lot to Michael for the inspiration:
https://www.youtube.com/watch?v=SorB6LBTeH0

Thanks a lot also to Alexander:
https://makerworld.com/de/models/879532-godox-mf-12-diffuser
The taking over of the clamping mechanism saved me a lot of time, even if i had to tune it a little bit for my purpose.

And last but not least to Jan for the idea of layer separation with a permanentmarker:
https://www.youtube.com/watch?v=tKTcPEfuboI

 

Disclaimer
All my projects are in a stage of prototype. I refuse any liability for damage of the printed part or your equipment or injury/infringement. 
By downloading it, you print and use it at your own risk

https://www.cazul.de/impressum
 

Tagi