1 / 16
Energy Monitor (full project) — zdjęcie 1
1 / 16

Energy Monitor (full project)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

EnergyMonitorArduino energy monitor, using SCT-013-030 current sensorsProject Links :Software part, on GitHubHardware…

Ocena
0 / 5
Polubienia
1
Pobrania
7
Wydruki
0
Wyświetlenia
94
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

EnergyMonitor

Arduino energy monitor, using SCT-013-030 current sensors

Project Links :

This is a full energy monitor project :

  • You can manage 1 to 6 sensors.
  • You can configure it through USB (see below).
  • It can communicate through USB, with any homemade software.
  • It can communicate with any Home Automation System supporting MySensors (I'm using Domoticz).
  • Full source is provided, you can customize it.

Needed parts :

Instructions :

  • Before to print case, you can specify how many sensors you have.
    • You can define the exact number of sensors, or plan more. Each socket will be pre-cut for future use.
  • Follow joined scheme for assembly.
    • Each sensor have to be connected to A0, A1 and so on...
  • Upload sketch to the Arduino Nano.
  • Connect it to any computer for configuration (see below).
  • Let's play...

Configuration parameters :

  • Number of sensors,
  • Sensor calibration (Vrms, ICal, IOffset),
  • Sample frequency,
  • Transmission frequency,
  • Toggle MySensors on/off,
  • Toggle serial output on/off.

Configuration will be saved to eeprom.

Using serial console, you can communicate with the sensor. For example, using minicom (? for show help) :

$ minicom -b 115200 -D /dev/ttyUSB0 __ __ ____| / |_ _/ ___| ___ _ __ ___ ___ _ __ ___| |\/| | | | \___ \ / _ \ _ \/ __|/ _ \| / __|| | | | |_| |___| | __/ | | \ \ _ | | __ || ||__, |____/ ___|| ||/\/|_| |/ |/ 2.3.1Energy Sensor has powered upEnergy Sensor (can use up to 6 sensors)F0: : Sample frequency in seconds (F0:5)F1: : Send frequency in seconds (F0:60)E#:[0|1] : Enable Sensor # (E0:1[;E1:1])V<#:val> : Set Vrms (V0:230[;V1:230])C<#:val> : Set ICal (I0:29.95[;I1:29.98])O<#:val> : Set intensity offset (O0:0.05[;I1:0.07])S[0|1] : Toggle Serial outputT[0|1] : Enable MySensors transmissionM<#> : Sensor mode (1: power, 2: current, 3: power+current)all commands are case insentitiveF0:2;F1:60E0:1:V0:230:C0:29.40:O0:0.01E1:1:V1:230:C1:32.00:O1:0.05S0;T1M3Latest lines show current configuration.

Warning : If you are using SCT-013-000 instead of SCT-013-030, you have to add burden resistor. NRF24L01 may have connection issues. You have to add 10µF capacitor between PWR and GND.

You'll be handling dangerous voltages. I decline any responsibility in case of any incident or accident.

Print Settings

Printer:

Anet A8

Rafts:

Doesn't Matter

Supports:

No

Resolution:

0.2

Infill:

25%

Category: Electronics

Tagi