Liczymy pasujące modele…
I designed a Wallmount for the Bosch EBike Charger with 6Ampere. It is a little bit bigger than the other ones (2 Ampere or 4 Ampere). You can use this design for every Bosch Ebike charger Happy Printing. :-)
For my bike charger I found a.m. charger wallmount. The basic function (holding 4A-charger and mains cable) were excellent. I added a plug holder sidewards for the battery plug. So everything is safe! After installation I saw that the…
Case for DSN-VC288 voltmeter-ampere meter. The hole is for the DC Power Connector 3-Pin 5.5 x 2.1mm (https://a.aliexpress.com/_EJAbB9W) 0.2 mm
Case for Deek Robot Power Meter. Print settings: Material: PETG Nozzle: 0.4mm Layer: 0.2mm Infill: 100% Support: YES (like last picture) What you need: 4x 3mm threaded insert 4x M3 screw 4x 4mm banana socket 1x switch (d=6mm) 1x 9V…
Just needed to measure the power consumption of LED strip in another project . Quickly drafted and made of PETG filament. The casing accommodates a cheap volt-ampere meter module (with a 2-line 3-digit 7-segment indicator). The top part…
The handle to my wife's Pampered Chef mini serving spatula cracked, so I designed a replacement. I printed with TPU, so it would be soft and comfortable, but there are fillets to help with comfort even if you use a harder plastic. I…
an enclosure for the cheap LED Volt-/Amperemeter. you need: Volt-/Amperemeter 3 Banana-Jacks 1 7x7 on/off switch (optional) 1 JST-Connector (optional) circuit board for easy switch and connector mounting wiring: OpenScad file included, so…
You can use it from bottom or top down. The Ampmeter will fit from both sides. Thickness is 20 mm, the frame is not closed. You are able to remove the ampmeter in both directions by rotating it 90° (very comfortable if the cables are…
Ordered three cheap volt/amp meters from ebay and hooked them up on my Hephestos, top one is for Arduino, motors and extruder, middle one for heatbed and bottom one for my Raspberry running OctoPrint. Take out the top to screws of the…
Fits the Pampered Chef paring knife (Item Number: 100034) Print on long edge w/ brim for best results.
This is a replacement cap for the old version of the pampered chef icing decorator. I designed it a bit sturdier than the original cap. The spherical indicator on the cap will line up with the rectangular indicator on the tube to make cap…
This for the ring that holds the cake decorator nozzle on for model 1775. This is for the model that has two tabs that lock in place and not the newer threaded 1776 design. This ring is known for cracking. I would suggest hand washing…
https://www.fritz-berger.de/artikel/berger-kofferbox-tampere-130789?varid=121228&partnerid=46A&xtor=SEC-97[520_Smart_Shopping_CSS_PPF_A]-GOO-[A]-[b]-S-[733190]&gclid=CjwKCAjw_b6WBhAQEiwAp4HyIMD2m4M9EuWUbXwa35U_JE7VEQwUUQGbAOtjTYdqKctCw5FlZ…
Free to download! printed with Anycubic Kobra 3 Combo, the 3mf worked for me the best.
This is the DXF file for the Milliampere Meter Housing for Co2 lasers. The file is made for 6mm plywood, and to get a good fit you would want to use correct kerf compensation, but works with no compensation too. The magnets are 20x7 mm…
Pampered chickens live here sign L 160mm w 80mm D 4mm For all you chicken lovers
Simple case that houses a multimeter (display) and a power switch, the case can be screwed to a surface. CAD files included, feel free to reuse. Components used: Multimeter https://www.amazon.de/gp/product/B08NTMX62K Powerswitch:…
Super simple replacement finger ring for the Pampered Chef steel mixing bowls. The original black plastic ones break over time, and the bowls are much less usable when that occurs. My set of mixing bowls is fairly old, but for reference…
Housing for a K50 amperemeter. I took this 30mA versio: https://www.amazon.de/gp/product/B07VJ3GYPS?th=1 The bottom part can be screwed with 2 M4 screws to the K50 and holds 2xM3 nuts The Top part can be screwed with M3 screws from the…
A parametric sheath with parameters specific to the Pampered Chef Quikut Paring Knife #1250. These came with carboard sheaths which these replace. The parametric model can be adjusted if the blade fits too tight or loose based on your…
Original retaining ring broke. Made this as a replacement.
Voltmeter-ampere meter case charger (DSN-VC288)
This thing was made with Tinkercad. Edit it online https://tinkercad.com/things/g1vFJBOX838 Use this to monitor 2 power supplies ,both volts and amps Two temperatures, extruder and print bed in both Fahrenheit and centigrade. Two LEDs…
Der Notaus kann ganz normal eingesetzt werden, das Amperemeter muss jedoch eingeklebt werden. Amperemeter Link Notaus Link
The racks take up a lot of space in the kitchen. That's why I came up with something else to store them well anyway. Depending on how many you have of the racks can also be installed stacked. Print instructions no support needed print in…
This case can be mounted on a DIN rail and holds an amperemeter gauge (like the HKS-VA028_V2.0) and the complemeting shunt resistor. This case can take the big 100A and also the smaler 60A shunt. .step available too for you to modify…
Gehäuse für USB Tester siehe. https://de.aliexpress.com/item/1005002371533933.html?skuId=12000020382751022&pdp_ext_f=%7B Deckel und Gehäuse haben Nasen und passen stramm zusammen. Deckel kann nach Bedarf beschriftet werden. Gedruckt Mit…
DH670 Voltmeter Amperemeter Halter mit Winkel und Schraublöchern Positiv getestet mit PLA und 60% Infill. Dieser Halter dient zum befestigen eines DH-670 Volt oder Amperemeter mittelts Verschraubung als Winkel.
Tampered Drink Dice. Print with 100% Infill Pause at Layer ≤ 4.5mm and insert some Neodym into the holes (Don't overfill!) If you put correspondent Magnets in the holes of the Ring you get full control of the dice
Dies ist ein Gehäuse zur Aufnahme eines 30mA Ampermeter zur Montage am Lasercutter This is a case for mounting a norma 30mA Amperemeter to the laser cutter
V1 has rounded edges to match the original part, however printing that with the largest face down did not work for me with PETG. V2 doesn't have that rounding and printed perfectly for me.
Replacement knob for your Pampered Chef chopper.
Pampered Chef Stackaable Cooling Rack - replacement rubber foot. A bit larger then the original ones - should hold much longer I suggest to print these from TPU.
Andre-Marie Ampere Bust is a digital STL model prepared for 3D printing. Preview renders show the supplied geometry from multiple angles. Choose scale, orientation, supports, layer height and material for your printer. Digital file only;…
My sister in law purchased a Pampered Chef Easy Access Decorator at a garage sale and it was missing the screw on end cap. This is for the screw on version of the decorator. There are other replacement parts for the twist on attachment…
Our Pampered Chef Icing Dispenser broke when building a gingerbread house (really thick icing) - the plunger part broke. I took it apart (pull the top off), and found it was repairable... after sliding the broken plunger part off, I took…
Holder Clamp Amperemeter UT203R for screwing on the wall. With holder for measuring probes and cable
Our Pampered Chef Icing Dispenser broke when building a gingerbread house (really thick icing) - the plunger part broke. I took it apart (pull the top off), and found it was repairable... after sliding the broken plunger part off, I took…
Pampered Chef Stackaable Cooling Rack - replacement rubber foot. A bit larger then the original ones - should hold much longer I suggest to print these from TPU.
Simple volt ampere meter to debuging voltage and ampere while doing your electronic engineering hobby. Another material needed: 1x 5mm bolts or M5x12mm bolts for the Arm (You can change this up to 18mm length) 1x 3mm bolts for DC socket…
3D printable topographic miniature of Tampere - 🇫🇮 Finland Capture the beauty of Tampere 's city landscape with this topographic miniature! This 3D model represents the geographic area around the geo coordinates 61.498, 23.762 (LatLng) .…
The rack takes up a lot of space in the kitchen. That's why I came up with something else to be able to store them well anyway. These can be attached best with adhesive pads from 3M in the size 50x25mm. These just need to be cut in half.…
a drone photo i took a few years ago converted into a lithophane - this came out really nice
replaces the clear domed lid. This one is flat so one can stack shakers. Fits snug on the older/original shakers. a bit loose on the new shakers. Print it upside down and no supports are needed. Prusa Slicer (maybe others) allows one to…
These knives are really sharp and I always worry about getting stabbed when I put them away in their original holders. I made this simple cover to replace the original. It is much safer. It prints in vase mode, 0.2mm layer height. I found…
milwaukee 12 volt 4-6 ampere battery replacement parts
milwaukee 12 volt 2 ampere battery replacement parts
I have made a 220V AC European socket test box, with which one can measure Amps of a device if necessary. The test box can also be used as a power socket by the application of the switch. The switch in position 1 is power socket only and…
![[ Laser Cut ] Milliampere meter (Ammeter) housing for Co2 laser.](https://media.printables.com/media/prints/199222/images/1838008_df624d68-68ec-44fd-b24b-6c6b126e6bdc/dsc_0350_s.jpg)
