Self Watering Kits for IKEA Sojaböna & Muskot Pots
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
☼ Wicking ☼ Aerating Root-Limiting Mesh ☼ Filler Flap ☼ Gravel Tray ☼ Fill Indicator | ↔ Sojaböna 12, 15cm ↔ Muskot 12cm
- Ocena
- 0 / 5
- Polubienia
- 46
- Pobrania
- 39
- Wydruki
- 0
- Wyświetlenia
- 732
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Home Decor
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Summary
Sojaböna is the new Muskot
IKEA's ceramic plant pots are shiny, durable and affordable. In my view, there's no need to print a plant pot unless you require an unusual shape.
Further, many IKEA pots have a handy internal lip a few cm from the bottom - as if someone was going to add a partition there and create a water reservoir in the base. But I never saw any such product offered by Ikea, so a few years ago began making my own (models 552349, 552344).
Although they worked very well, this redesign has some improvements, and adds optional features:
↑ Faster filling
↑ Inspectable wick aperture
☼ Aerator / Root Limiting Mesh (optional)
☼ Filler Flap
☼ Gravel Tray (optional)
☼ Fill Indicator (optional)
Wicking method
Using irrigation strings to wick water up into the soil is a superior method of self-watering, as the soil doesn't get excessively waterlogged.
Channelling the wick to emerge near the surface, makes the reservoir less prone to being overgrown with roots. And it's even possible to clear away roots from the portal if required.
Supported Pots
► Sojaböna 15 cm | 12 cm (more sizes will follow *)
► Muskot 12 cm (not sold anymore but I have loads of them)
* If I have the time and inclination, but there is a FreeCAD source model for others to remix !
Other bought items
- Irrigation wick / self watering wick, 7 mm diameter. Preferably a synthetic type that's non-rotting.
[some possibilities] - Compost (making your own is much more satisfying!)
- Coarse gravel (optional)
- Varnish (optional)
- Cling film (optional)
Printing and Assembly
see images for print orientations
- Bulkhead (floor, partition)
It has a hole in which to insert the Tower part, therefore use appropriate offset to correct for known hole size bias of your printer ("Horizontal Expansion" setting in Cura).
- Tower
Needs a tiny bit of support under the filling recepticle.
Ensure your printer can do overhangs of 60 degrees.
Clear the internal channels of stringy residue as best you can, especially if installing the Level Indicator.
- Lid
There are two options, one of which has a notch for the Level Indicator.
A coat of varnish on the Lid's surface can help to prevent dirt and staining.
- Level Indicator Float and Stem (OPTIONAL) [experimental feature]
For me, the Float printed best on a raft, and then needed a bit of scraping to remove all residue from around the stem hole.
For the Stem, I used a brim. Likewise, it's important to remove any residue that could impede the smooth motion of the stem.
Insert the Stem into the Float by gripping with pliers very close to the flange. It's a tight fit. (see image)
Apply varnish to the Float and joint if uncertain of the watertightness.
Apply graphite pencil to the Stem to reduce sticking.
Install the Level indicator up the filling channel of the Tower, passing it through the small guide hoops which should be free of all residue.
→This is an undeveloped feature and doesn't work perfectly. Basically it can stick in almost any position and mis-state the water level. Shaking the pot gently from side to side can free it for a truer reading.
- Aerating, Root-Limiting Mesh (OPTIONAL) [experimental feature]
Allowing air around the soil is supposedly healthy for the plant, and aims to reduce “pot bound” roots that spiral into a tangled mess.
The Mesh prints in sections that clip together before installation.
The Meshes (thus far) are designed for only two print layers in the “meshy” part. Ensure your layer height, and initial layer height, yield a first layer in one direction and a second layer perpendicular. The third and subsequent layers should be unmeshy, containing only the spacer bars and the clips. (see image)
→ At the time of writing, I don't yet know how well this feature is going to work.
- Gravel Tray (OPTIONAL)
Gravel can decorate and reduce evaporation.
Using the Tray keeps the gravel more dry and clean. Also it can be removed quickly if needed.
If also installing the Aerating Mesh, then trim off the centralising lugs from the Gravel Tray (see image).
- ASSEMBLY NOTES
When I assemble these, I add some cling film over the top of the bulkhead, which helps to seal the partition between soil and water. If you do this, make a hole in the film where the tower will attach, and after assembly ensure that all three channels in the tower are unblocked. (see image)
The wick is best inserted by temporarily connecting a thin string or wire, with which to drag it through its channel. Ensure enough wick hangs out at the bottom to reach the base of the pot.
If installing the Level Indicator, ensure the wick doesn't trail into the path of the float (see image). Rotating the assembly anticlockwise, as you lower it into the pot, can help. Grip the top of the indicator stem as you assemble, to prevent it dropping out.
Source Model / Remixing
I include FreeCAD source models for the Sojaböna variants.
It's a mostly paramentric model, but unfortunately not robust when parameters are changed substantially.
If you want to attempt a new variant, I recommend to begin with the newest .FCStd available (presently Sojaböna 12), as this will have more internal improvements for remixability.
It can take a long time for the model to regenerate, so before changing any parameters I strongly recommend the “skip recomputes” option in the model tree.
To make dimensional changes, find the parametric Spreadsheet in the model tree.
I've grouped the spreadsheet parameters into two categories:
- Base parameters which mostly capture the Pot dimensions. All these need to be measured and entered into the blue cells.
- Feature parameters which can optionally be adjusted, or otherwise left to their default values. These parameters also have max and min limits.
For the feature parameters please don't edit their blue cells† directly. Edit the orange cells, or set to -1 to use an autocalculated default value.
[† blue cells are ones that directly feed the model]
After changing the necessary parameters, recompute manually if needed.
The model will almost certainly fail, often due to internal sketches mangling their line directions, and similar annoyances.
I recommend to open the original model alongside the changed one, and compare each failed sketch in turn with its original so that you can see how to fix it.
FreeCAD has certainly gotten more robust with v 1.0 , but still isn't as clever as professional CAD when it comes to updating internal references and managing the effects of that.