1 / 5
Jonsbo Z20 Dust filters and long legs — zdjęcie 1
1 / 5

Jonsbo Z20 Dust filters and long legs

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Dust filters and long legs for Jonsbo Z20

Ocena
0 / 5
Polubienia
4
Pobrania
37
Wydruki
0
Wyświetlenia
559
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Computers
Licencja
Creative Commons — Attribution

Sorry, my English is bad, this is google translate.
My experimental project of dust filters for PC, which was motivated by the original filters from the excellent compact case Jonsbo Z20, which perfectly protect against mosquitoes and other not very small insects from getting inside.
The material chosen for filtration was a nylon mesh with cells "100 mesh" https://sl.aliexpress.ru/p?key=n3m3V4q (Diameter about 0.1 mm. According to advice from the Internet, it is better to use 80 mesh, but I did not find it for sale in black).
Then I looked for options for attaching this mesh on the Internet, but no one bothers and just sticks magnetic tape, which categorically did not suit me from an aesthetic point of view. As a result of various experiments, I found a fairly convenient option for myself using a soldering iron. The process is quite simple:
Print parts from PETG. (I don't know how it will work with PLA, there may be problems with its melting temperature, or maybe it will be better)
Use a soldering iron with variable heating temperature and preferably a thin tip.
Set the temperature to 160-165 degrees Celsius (higher there is a risk of melting the mesh itself)
Place the mesh on the part and slowly, with pressure, move the tip along the grooves.
Cut off the excess pieces of mesh (I did this with a knife using a ruler)
The result can be seen in the photo.
To attach to the case, I used magnets with a diameter of 3 mm and a thickness of 2 mm. In my case, they were inserted tightly, but if desired, you can squeeze a drop of superglue inside.

P.S. The original legs of the case are very low, they limit the air flow to the video card, so I also modeled longer ones. Printed PETG + TPU A95. In the end, I did not need them, since I installed the computer on brackets, but perhaps they will be useful to you.

----------------------------

Мой экспериментальный проект пылевых фильтров для ПК, мотивацией для которого послужили оригинальные фильтры от великолепного компактного корпуса Jonsbo Z20, отлично защищающие от проникновения внутрь комаров и других не особо мелких насекомых.
В качестве материала для фильтрации была выбрана нейлоновая сетка с ячейками "100 mesh" https://sl.aliexpress.ru/p?key=n3m3V4q (Диаметр около 0,1мм. По советам из интернета лучше использовать 80 mesh, но я не нашел ее в продаже черного цвета).
Далее искал варианты крепления этой сетки в интернете, но никто не заморачивается и просто клеит магнитный скотч, что меня категорически не устраивало с эстетической точки зрения. В результате различных экспериментов нашел для себя достаточно удобный вариант с использованием паяльника. Процесс достаточно прост:
Печатаем детали из PETG. (Не знаю, как это будет работать с PLA, с его температурой плавления могут быть проблемы, а может наоборот будет лучше)
Используем паяльник с изменяемой температурой нагрева и желательно тонким жалом.
Устанавливаем температуру 160-165 градусов цельсия (выше уже есть риск плавления самой сетки, чего нам категорически не нужно.
Кладем сетку на деталь и медленно, с нажимом, проводим жалом по канавкам.
Обрезаем лишние куски сетки (я делал это ножом с помощью линейки)
Результат можно увидеть на фото.
Для крепления к корпусу использовал магниты диаметром 3мм и толщиной 2мм. В моем случае вставились плотно, но при желании можно выдавить внутрь каплю суперклея.

P.S. Родные ножки у корпуса очень низкие, ограничивают приток воздуха к видеокарте, поэтому смоделировал также более длинные. Печатал PETG + TPU A95. В итоге они мне не пригодились, так как установил комп на кронштейны, но возможно пригодятся вам.

Tagi