Liczymy pasujące modele…
Introduction/Support Me: If this 3D design helps you optimize your PC's cooling, please consider hitting "Like" on this model file! Your support encourages future designs. You can also support my work by purchasing items for this setup…
Since the Jonsbo N2 originally only comes with a quite loud “slim” (15mm deep) 120mm fan in the back I wanted to swap it out for a quiet fullsize (25mm deep) fan. Unfortunately due to the very limited space in the back of the case this…
This is my addition to the Jonsbo N4 case to keep disks at safe temperatures. The magnets used are 2 mm thick and 8mm in diameter (4mm radius). The fans used are: ARCTIC P12 Slim PWM PST 120x15 Printed on Bambu Lab P1S with a black matte…
V1.2 Noses should fit into original slots. Better clearance Add slim Version (i.e. Arctic P12/P14 Slim)
Remix of the “ Jonsbo N4 - 2x SLIM Fans Front Adapter ” This version uses 10x2mm magnets. STL available as one piece or two pieces. Used the same fans as the original ARCTIC P12 Slim PWM PST 120x15 (affiliate link) Printed on Bambu Lab…
This is a taller version of the foot from the Jonsbo D31/D41 series of ATX computer cases. The purpose is to increase the gap under the case and improve airflow into the lower intake fans. The gap with the tall feet is now approximately…
About The included 3MF/STL files are based on a 5mm diameter x 3mm height neodymium magnet. The Fusion file is included if you have different sized magnets, changing the parameters will adjust the model. No modifications are necessary to…
Large bed only. (6/2/2025): added 25mm height fan model Print with support.
UPDATE: I slightly tweaked the HDD baseplane, now the hdd slides perfectly. Every tenth of a millimeter counts. UPDATE 2: I modified the HDD part and removed the extrusion. I uploaded the full fusion 360 file under the name v2.1, and the…
Adapter to mount a 2.5" SSD or HDD into the 3.5" bays of the Jonsbo N3 and N2 . Designed for a snug fit with the stock drive trays, no tools or mods needed. Print Info : PLA, 15% infill 0.16mm layer height No supports ~4.5 hour print…
The Jonsbo N2 only has an option to mount one 2.5'' SSD to the case. With this holder you can mount a dual stack of SSDs to the same spot. 4x M3 heat set inserts required
You may be thinking - another front fan mount?… Yes, though this one is different from all the others I have seen. I personally didn't like the fact other designs added an additional section in-between the front plate and case.…
The Jonsbo C6 ITX Tower has notoriously bad air flow. These panels let enough air through. No supports, no additional parts required, just print an install. I included: Meshed versions which I created inside orcaslicer with a modifier…
The Jonsbo N2 is a very pretty case for a relatively compact home NAS. Unfortunately it doesn't come with a way to add a case/CPU fan. With this holder you can easily add any 120mm fan for better CPU cooling. M3 heat set inserts required…
Designed this bracket to use in my Jonsbo D32 mATX PC case, but works with other cases as (see list below). The CPU cables provided with my Corsair SF850 power supply were relatively short and struggled to reach between the motherboard…
This is a simple drive bay adapter designed to fit into NAS cases, specifically the Jonsbo N2 using the included mounting hardware. It accepts a 7mm 2.5" laptop-style drive and allows it to be inserted into a hot-swap bay. As the drive…
The Jonsbo NV10 isn’t well known for good airflow along the GPU side panel, so I designed a custom panel to replace it with something that provides significantly better airflow. It’s designed to work with two 92mm slim fans and a…
2 Part front adapter to add standard pc fans ot the front of the jonsbo n4. Printed on Bambu Labs A1 mini with tree supports.
This is an adapter for mounting 2.5" SSDs into the 3.5" HDD bays of any Jonsbo N-series case (N1, N2, N3, N4, and N5). Please note that the default version is slightly taller than necessary in order to add additional strength to the screw…
Jonsbo N3 NAS Front Fan Spacer Included file for screw attachment designed to hold the two halves together with four M3 bolts. Slots directly into place within the case allowing for the original front grill to slot into the spacer. Fits…
What? A printable solution for mounting two 3.5" hard drives in your Jonsbo D31 computer case, while still allowing for a 120mm fan to be mounted at the front. Note that this requires you to be running a 140mm long power supply in the…
The Jonsbo N1 is a sleek and modern RAID tower case perfect for a DIY home office server. Set up as a virtualization server, however, the CPU and mainboard area becomes hotter than ideal. Air from the front fan disperses en route,…
Printed with Bambu lab White ABS on a Bambu lab X1C The current solutions using extensions don't look very appealing, so I decided to design a front panel that accommodates fans - it's a complete replica of the original, except for the…
Plastic screws for securing the hard drive to the Jonsbo N2 bay.
This simple mod will allow you to install two thin 92 mm fans without additional fasteners with standard fasteners that often come with them. The bracket is installed in the upper and lower bars in the spacer. To do this, they must be…
Three styles of substitute faceplates for the Jonsbo N1 PC case, with vents and 3.5mm mesh clearance, for greater airflow and lower thermals. Simply attach it by using your original faceplate screws and 3D printed washers (no rubber…
The hard drives in the Jonbo N5 ran a bit too warm, so I decided to redirect airflow from the upper front of the case down to the hard drive “basement”.
Jonsbo/Jonsplus Z20 Feet Riser It's 30mm high, but even if it's higher than this, there's no change in temperature, so I think it's the best length Based on the Thermalright TL-S12 system fan 1000rpm I'm using, the internal temperature…
Hey, I was trying to improve the airflow in the drive bay of my Jonsbo N4 Homeserver case, and I saw that there is a vent above the PSU, and since air takes the path of least resistance, I assume that a lot of the air being sucked out by…
Print as per 3MF with supports enabled for the four corners where the screw holes are.
An 8 bay 3.5 inch HDD enclosure designed around the Jonsbo N3 backplane which can be purchased separately for ~€15. I have also Included a mounting piece for the Thermaltake CoreV21. The main assembly is fastened to the mounting plate…
A Cable Hole Cover for the Jonsbo N1 computer case. The many backplane SATA and power cables, in the bottom cable access hole, may push out and rub on or catch on the outer shell. This cover keeps those cables inside and protected. The…
I don’t like the wooden front panel of this case — it doesn’t match my interior design or aesthetic preferences at all. That’s why I made a plastic one to replace the original. The PEI coating on the 3D printer bed gives the surface an…
Front panel with "mesh", blank, and diagonal variant. Image 1 showcases the mesh variant, with a version with some window screen glued on the back. Image 2 showcases just the mesh variant, and Image 3 showcases the blank Updated 14 Jan…
This is an internal mounting adapter for a Jonsbo N5 case for mounting six 2.5" SSD with a 120mm fan for cooling. Required Hardware 24 - M3 button head socket screws - 6mm long Print Settings I printed it with PLA. PETG would be a better…
If you have SFX-L power supply you can use this adapter to fit SFX-L on Jonsbo N3 case. I already purchase the case before realise it only can fit SFX below 105mm. After some measurement, the SFX-L PSU can barely fit if there is adapter.…
Printed with White PLA+ eSun (230°/60°) on a Creality Ender 3 V3 SE. The goal was to make a first prototype before doing it in PETG or another material more suitable for a computer piece. For now it fits very well and can hold fans. I…
Compatible feet to raise bottom case clearance to 32 mm / 1.25 in. Recommended to print with the widest base section to the bottom and not add support to the overhang section.
Just your standard 120mm Fan Grill, stylized to match the Jonsbo D30/D40 top grill pattern.
This is a two part component. It is a 2x 140mm shroud for the Jonsbo N5 to be mounted in front of the drive bay. The original wooden slotted cover will mount on the front of this component. I designed this component to fit my very…
This is a mod I created for the Jonsbo N4 case. There are already some great mods to help with cooling, but none of them help with airflow out of the top of the case. This mod allows for two 120mm fans to be installed on top of the…
Utilizing the existing HDD/SDD holes. Left off centered to minimize cable interference. Holes use a M3 x 5mm heat insert. I used 20mm long M3 bolts on my TL-9016 fan. And 6mm long M3 bolts to attach the mount. I'd recommend using a thin…
I wanted better temps for my system so i modded a duct for fresh air intake and a mount for 2x 120mm fans in the bottom. For the 2x 120mm Fan shoud in the bottom you need to cut out some parts that are in the way and also need to remove…
I recommend gluing the clips into the holes. This screen mount is made for the JONSBO D41 PC Case. The case has a built-in, detachable screen, allowing me to have a video or reference model up without having to take up more desk space…
This case mod allows you to add 4 additional drives. It uses the standard Jonsbo 4 disk backplane found on the N4 and N5 case series. It can be easily purchased from many stores on Aliexpress . There is enough room for a standard…
The original front/side panel retention clips on the Jonsbo D41 computer case are lousy and brittle. I decided to make these when I accidentally broke 3 of the original clips when attempting to put my side panels back on. I was able to…
Jonsbo N6 Nas Case Front Fan Mount For 120x15 Fan 25 Percent Infill, ( Tested with 15 and it was still plenty strong ) Needed Parts 4 m3x12 Bolts 4 m3 Nuts 2 Magnets And Screws From Old Front Plate 2 120mm by 15mm Thick Fans 8 Course…
11-3-2025 Update New version uploaded that includes a 120mm fan for cooling. https://www.printables.com/model/1469160-jonsbo-n5-internal-25ssd-x6-mount-v2 9-1-2025 Update. I updated the mount to allow for better airflow and reduce the…
Jonsbo N1 Vented faceplate for better airflow. M3 screws, nuts and spacers are needed for attaching the faceplate to case. Font i/o pannel modified to fit 3x 3mm leds for server work indication. Can be mounted with stock screws.
Here english version: -> weiter unten in Deutsch I bought the Jonsbo N5 server case because it allows up to 16 hard drives (12x 3.5-inch (HDD) and 4x 2.5-inch (SSD)) and the design also makes the hard drives hot-swappable. After I had…
These brackets allow an SFX power supply to be mounted with its connector side facing the existing cable channel on the Z20 computer case, in the style of BTS or Project Zero motherboards. This cleans up the interior of the case and might…
Simple elevation for the feet of the Jonsbo C6. So that more air can enter from below.
2 SSD 2,5" I use M3 nuts and the SSD screws
i wanted to have a Hotswap Bay for SSDs without using the 3.5" Trays for HDDs so i used the SFX Mount for a 4 Bay SSD Hotswap bay. This only works if you use a PicoPSU or similar because you cant use any SFX PSU anymore. The Cable used:…
Simple fan bracket for your LSI cards in an Jonsbo n5 Mounts horizontally or vertically with standard self tapping fan screws
Follow the instruction to build firmware for Arduino Nano
What? A printable solution for mounting an extra two SSDs behind the motherboard tray in your Jonsbo D31 computer case! This brings the total SSD capacity up to 5 drives, but (potentially) more importantly, this puts three SSDs close…
Title says it all. Designed for a somewhat wide perimeter line and 0.2 layer height print. Print as shown on a screenshot.
Jonsbo N3 Backplane Rack Mount This model is designed to mount the Jonsbo N3 Backplane within a 10-inch rack , providing a secure and space-efficient solution for NAS (Network Attached Storage) system builds. The bracket allows for clean…
Cover for the Jonsbo N1 front I/O and faceplate holes to make the front look nicer if not using the faceplate. Contains a front I/O cover, two screw hole covers, and four nuts so you don't need any other hardware to secure it. The front…
My buddy grabbed a Jonsbo N4 case second hand, missing nearly all of the hard drive grommets, but we had the screws. Threw together a print, and used TPU 95A to print them out. Works great for that OEM feel. From the look of things, this…
This is the front cable cover of the Jonsbo Z20 case With the case on the side, I made a cover that covers the cable because it keeps showing. It's fixed to the frame using a 6x3 magnet At first, I wanted to follow the design of the case…
Design this to add color and airflow. used the screws from origial frontpanel Screw holes are tight, so i drilled they a bit. be carfull the standoffs break easy, i lost one feel free to redesign
Mount multiple 2.5" drives on the sides of a Jonsbo N5. Screws in the side bars using standard fan screws, and the disks mount with standard disk screws. Optimized for printing without supports. Recommend PETG or better (disks may get…
1x Backplane: https://www.aliexpress.us/item/3256808318459164.html 1x Rails: https://www.amazon.com/dp/B08S6T53VW 17x Heat-set inserts: M4x0.7 6.4mm: https://www.mcmaster.com/94459A160/ 5x PCB Bolts: M4x0.7 6mm:…
This feet makes use of the original screw. Have a spot for glides.
Jonsbo N6 rear fan mount, the round holes in the oem mount where extremely noisy for me. This mount quiets it down to a bearable level.
A custom display system for Jonsbo N4 PC case, built with ESP32-P4 and LVGL, designed to monitor and display system information in real-time. Code for ESP32: https://github.com/keitetran/JonsboN4Monitor ESP32 Dev board:…
I create all my models in my free time. If you'd like to support my work, I would really appreciate a small donation. ☕ ℹ This model allows the installation of 2x 120 mm fans while retaining the original front cover. UPDATE 2026-07-09:…
Designed to allow installation of 2.5" SSDs in the 3.5" bays of Jonsbo N series case. I tried another design that I got off Printables and it didn't fit, so I designed my own. It has sprung clips that hold the SSD in place, and the top…
Printable mounts for mounting 4010 exhaust fans (e.g. NF-A4) to help with airflow in the Jonsbo NV10. Requires removing the side panel mount brackets and replacing the clips in them with the prints themselves. Triple fan mount has cable…
Useful if you're using an HBA and wind up with a lot of extra sata connectors. Also gives you some flash redundancy over that one 2.5 bracket that comes with the case. Hangs off of the SFX PSU and sticks to the top of the internal space.…
This addon adds a 6 2.5" sata bay. The bay is designed for SSDs without rgb and so on. dont use RGB 2.5 SSDs or HDDs, they will overheat. Use M3x3x4.2 heated inserts (4.2mm is the outer dimension and 3mm is the length). i am not happy…
Upgraded the model with reinforcements and 0.2mm solid layer in the bottom of the hole. Installs to the original location with original screws. I reused the original pads from the original feet. I put a single solid layer to the bottom of…
Drop-in replacement for standard foot with increased height and added hands. Side panels removable without any issues. Can be used in combination with Tall Feet for Jonsbo D31/D41 Series. Just mirror the model to have second side. No…
A simple headphone stand that mounts on your Jonsbo Z20 PC case. The fit is quite snug, so you may need to apply some force to install it.
Original front panel is boring for such a great case, so i decided to make it better. Hope you like it ^_^ You will need 3d printed parts (pla/petg/abs) 4 magnets 5x2mm 10 strips of nice wood 345х16х5mm + oil for wood glue First you need…
I needed to mount an additional NVMe SSD for a ZFS cache in the Jonsbo N4 case. This bracket makes it possible when using a Mini-ITX motherboard, as it mounts using the unused Micro-ATX standoffs. The source OpenSCAD model is also…
It's a modified fan shroud for Deepcool Assassin 4 cooler made by Skagger. Now it is a back side (intake/exhaust, your choice) fan duct, you can split it and resize it in Z dimension with Fusion to fit your PC Case, it's 66mm to fit…
A relative Simple CWWK NVMe Backplane Mount for the Jonsbo N3 Case. Use M3x3x4.2 heated inserts (4.2mm is the outer dimension and 3mm is the length). insert the heated inserts like in the second image. Then mount the backplane and the…
Sorry, my English is bad, this is google translate. My experimental project of dust filters for PC, which was motivated by the original filters from the excellent compact case Jonsbo Z20, which perfectly protect against mosquitoes and…
Better rear mount for Jonsbo N6 rear with Fans on top of Sfx Psu.
This model serves to allow an easy way to add a handle or feet to the Jonsbo C6 computer case. I purchased one C6 with the stock strap and it was alright but then I needed a second white one and I could not find one with the strap. So I…
I bought this case 2nd hand and the seller forgot to gave me the extra clip. So I decide to re-draw one for the 3d print. Printed in ABS, suggest ABS, ASA, PETG. PLA might break or deform and loose. Customized for my printer so sale…
I’m using a mini-ITX motherboard inside a Jonsbo N4 case. The board has a single PCIe slot with bifurcation support, and I needed to connect three devices: a SAS controller, a 5GbE NIC, and an NVMe SSD. Hardware I used: Mustpoint Dual…
I had no use for the USB/Audio front panel connections and required extra room for another case mod, so designed a blanking plate that can be swapped with the stock PCB. Screws in with original case screws. The two halfs are split for…
PSU Adapter for HDPlex ATX 500W PSU . The adapter raises the PSU to allow clearance for the front IO daughterboard and certain motherboards with plugs coming out of the side. Uses 4x M3x8mm bolts to mount to the PSU because I don't have…
This Mod decouples the HDDs a little bit more (to be specific, the lower hdd tray and the backplane). This Mod is experimentell. You need 11 Bottom Damper and 7 Top Damper. they are installed in the lower tray (4 Bottom Damper) and the…
I saw this post on the TrueNAS forums and bought a PCI bracket that looked the same, but it was too thick and impinged on my heatsink! I couldn't put the top cover of the case back on at all! Ten bucks worth of bent scrap aluminum later…
Remix of the fan duct by D3Cove here: https://www.printables.com/model/377029-jonsbo-n1-fan-and-hdd-air-ducts My particular (Phanteks) fan left gaps that allowed air to escape so I added some solid parts to close up the gaps.
You will need to drill holes to the jonsbo case for the PWM to pass. This model rely on 10mm X 2mm magnets. The holes for the fans are designed for the screw provided with the noctua fans (0.4cm diameter) On top of that i installed a…
This little guy slides in between the GPU and the fans to stop the GPU fans from hitting the bottom fans. The two little pegs drop into the fans so it cant move or shift around after it is slid in. Print with the little pegs up. Just…
Vibrations add wear and tear to spinning disk drives, with my NAS located on the second story of my home about 20 feet away from a washing machine that vibrates my entire second floor, I decided to add some extra minor protection to it. I…
I love my Jonsbo N3 nas case, but I could never get the drives below 51c even without the drive bay cover off. I decided to make my own cover with fans for improved cooling. For this I used 2 Noctua NF-A8 5V PWM, Premium Quiet Fan with…
Had to quickly design those because the NAS wouldn't fit its old shelf (quite the tall case!); it's just enough height to clear the front panel tabs sticking out underneath the case, compatible with the existing screws; you can also not…
Dual Monitor mount for 15 inch (Arzopa) screens for SFF PC jonsbo T8 Plus Case Glue 2 Parts together ( Ender3V2 didn't fit )
This model is designed for the ASUS N100I-D mainboard inside the Jonsbo N2 case. It mounts directly onto the CPU heatsink and allows you to attach an additional 120mm fan. It's is also compatible with…
This is a custom 3U hard drive enclosure designed specifically for 10-inch networking racks (built around mklements Lab Rax). The enclosure houses the 5-bay aluminum hard drive cage, fan and backplane from a Jonsbo N1 case. Bill of…
A stand for a 7' Eviciv monitor powered by a Raspberry Pi 4 with a Kiosk mode, fitted to stand on top of the Jonsbo N2 Monitor type (can also be found on Ali-Express) EVICIV Raspb Pi Touch Screen 7"…
A PSU mount that place the SFX closer to the front and the top. BOM: 2x inserts M4x5 D6 2x inserts M3x4 D5 2x M4x12 or bigger 2x M3x10 D965B (can use smaller M3x8 should be ideal)
