1 / 10
8 Bay 3.5 inch HDD Rack with mounts for JonsboN3 backplane and Thermaltake CoreV21 case — zdjęcie 1
1 / 10

8 Bay 3.5 inch HDD Rack with mounts for JonsboN3 backplane and Thermaltake CoreV21 case

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

An 8 bay 3.5 inch HDD enclosure designed around the Jonsbo N3 backplane. Includes a mount for the Thermaltake CoreV21.

Ocena
0 / 5
Polubienia
27
Pobrania
144
Wydruki
0
Wyświetlenia
1283
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Computers
Licencja
Creative Commons — Attribution

An 8 bay 3.5 inch HDD enclosure designed around the Jonsbo N3 backplane which can be purchased separately for ~€15.

I have also Included a mounting piece for the Thermaltake CoreV21. The main assembly is fastened to the mounting plate using 12 x M3 screws. It should be straightforward to create a custom mount for any case or enclosure using these 12 mounting points.

Materials Required

  • Jonsbo N3 Backplane
  • M3 x 10mm wafer head screws - I haven't counted but a bag of 50 should be enough
  • M3 x 5.7 x 4.6mm brass heat set inserts - same as above I think
  • M3.5 x 5mm HDD screws - 4 or 6 per drive.
  • Optional M3 Paper washers can be used when mounting the backplane to the backplate
  • M4 x 20mm (I think) bolts and nuts to attach the mounting plate to the CoreV21 case - 12 or less of these I don't recall exactly

Instructions

I used PETG with 20% infill for all parts except for the HDD Rail which was printed in 95A TPU with 15% infill.

To assemble the rack and backplate:

  1. Print the HDD_Rack_Backplate.
    • Add brass inserts to all non through holes - the 7 circled in yellow in image #1 below will be used to mount the Jonsbo backplane. 
    • Add 3 brass inserts to each end of the backplate. These will be used to mount the end pieces
    • Mount the backplane now if you like or wait until later.
  2. Print Side_A and Side_B. Each side will need brass inserts added to all holes.
    • 5 brass inserts on the bottom face
    • 3 brass inserts in each end
  3. Print End_A and End_B - no brass inserts in these
  4. Mount sides to backplate
    • This must be done as shown in image #2 below as the slots in the sides must line up correctly with the SATA ports on the backplane. Pay close attention to the orientation of the truss on the backplate and the slots in the sides.
    • Attach each side to the backplate with 5 x M3 screws. 
  5. Mount ends to the sides and backplate.
    • The end pieces have only through holes.
    • Ensure that the counterbores are facing outward and use 9 x M3 screws to fasten each end.
  6. Mount the backplane to the backplate if you haven't already done so.
    • 7 x M3 screws
    • I used some PC motherboard paper washers here also but not strictly necessary

HDD Rails and Locks

For each drive you want to mount to the enclosure, print the following:

  1. 2 x HDD_Rail - I used PETG 20% infill
  2. 1 x HDD_RailLock - I used 95A TPU at 15% infill

The rails can now be added to the drives using standard HDD screws.

If you used PETG for the rails, 2 screws per rail is plenty. If you used TPU, I would recommend adding the third screw if available.

To assemble the CoreV21 mounting plate and rack assembly:

  1. Print the CoreV21_MountingPlate
  2. Add 12 x M3 brass inserts to the smaller holes on the top surface of the mounting plate.
  3. Now attach the mounting plate to the case.
    • I think I used M4 x 20mm bolts and nuts here. 
    • The nuts were tightened against the underside of the sheet metal tray on the case.
    • All holes on the mounting plate may not be usable so just use as many as is possible.
  4. Attach the rack assembly to the mounting plate.
    • The holes in the rack assembly should line up with the 12 brass inserts on the mounting plate.
    • Simply screw down with M3 screws

Image #1

Image #2

Complete Assembly

Tagi