Poorman's Dual Drive Extruder (BMG clone) for Prusa Mini
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Dual Drive Extruder for Prusa Mini/Mini+ (BMG style) with minimal BOM. Fits original Mini YZ mount.
- Ocena
- 0 / 5
- Polubienia
- 11
- Pobrania
- 19
- Wydruki
- 0
- Wyświetlenia
- 289
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Prusa Parts & Upgrades
- Licencja
- GNU General Public License v2.0
I wanted Dual Gear Extruder for my Prusa Mini+ but don't want to break bank for it.
So I bought ~$4 BMG clone hardware from Ali Express and printed case based on available models but non of them fit my needs. I decided to design my own housing remixing Prusa original step files with BMG clone I found on GrabCad web site (big thanks to anderfogel for his work).
The new extruder case is 12mm wider than original with motor rotated 45deg.
Reqirements:
- keep original filament path
- mount on original YZ axis
- reuse as much hardware from old extruder as possible
- make it cheap
BOM:
- 1x BMG clone hardware from Ali Express
- 1x M3x8 screw (from Prusa mini spare parts)
- 1x M3nS square nut (from Prusa Mini spare parts)
BOM (reused from original extruder):
- 1x Bearing 625 2Z
- 4x M3n hex nut
- 1x M3x40 (idler screw without spring)
- 3x M3x25
- 3x M3x12
- PTFE tube 4x2x150 mm
- PTFE tube 4x2x15 mm
- PTFE Fitting MINI
Printed Parts:
- Extruder Front
- Extruder Rear
- Extruder Arm
Print settings (m3f with all settings provided):
- Prusament PETG
- 0.2mm layer height
- 20% grid infill
- manual organic tree paint on support for Rear part
Assembly:
- Unload old filament
- Remove and disassemble old extruder (see original Prusa assembly instructions for help)
- Add 3x M3n hex nuts to front part (I suggest glue them with Super Glue as it will be hard to reach them one motor is in place)
- Add 1x M3nS square nut for Arm screw
- Add 625 2Z bearing
- Add M3x40 screw (must be inserted before motor)
- Install BMG shaft with filament gear
- Install motor gear
- Put front part to motor gear (mount with motor cable facing bottom or front)
- Screw 2x M3x12 motor screws
- Add small bearing to BMG shaft
- Mount Arm to Rear part and add filament M3n hex nut (glue if possible)
- Add PTFE tube 15mm, PTFE fitting (do not tighten yet as the part can break) and PTFE bude 150mm (secure with M3x12 screw)
- Secure Rear and Front parts with 3x M3x25 screws
- Mount on YZ rail using M3x40 and M3x8 screws
- Fasten PTFE tube fitting (slowly and carefully)
- Secure cable with zip ties
- Go to “Settings” → “Hardware” and long press knob on “Hardware” it will open experimental settings
- Set “Extruder steps per unit” to 415 and “Extruder direction” to “Wrong” than “Save and return”
- Load new filament and calibrate first layer
It prints perfect (see Benchy in photos). Next I'm considering adding IFS.
Enjoy :)
