1 / 1
Ominous Industries Social Robot
Zamów wydruk tego modelu
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Social Robot from the Bijan Bowen YouTube Channel.
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 9
- Wydruki
- 0
- Wyświetlenia
- 114
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- RC & Robotics
- Licencja
- Standard Digital File License
SzczegółyPliki (27)Wydruki i komentarze (Wydruki: 0) (Komentarze: 0)Remiksy (0)Kolekcje (1)Powiązane
More information about building this can be found here: https://github.com/OminousIndustries/SocialRobot
Here are the printing instructions for all files:
Printer Requirements
- Build volume: Minimum 256 mm × 256 mm × 256 mm.
- Material: No special filament required—choose your preferred PLA/PETG.
Recommended Print Settings
- Layer height: 0.20 mm (use finer layers on gears/sliders for smoother motion).
- Infill: 20 % baseline (increase for structural components noted below).
- Supports: Not required unless called out.
- Orientation: All STL files are pre-oriented for printing.
Part Checklist by Folder
Use the following checklist to track prints. Notes indicate parts that benefit from finer resolution, higher infill, or support material.
Base
- Base_Plate
- Gear_Rail — finer layer height recommended for smooth motion
- Motor_Mount
- Rail_Slider — finer layer height recommended for smooth motion
- Rear_Base_Mount
- Robo_Base
- Robo_Foot — print four copies
- Ten_Tooth_Gear — print with very fine settings and small layer height
Clamps
- Rear_Projector_Clamp
- Side_Projector_Clamp — print two copies
- Top_Projector_Clamp
Head Frame
- Face_Bezel — increase infill for strength
- Front_Crossmember
- Head_Frame — print two copies; increase infill for strength
- Rear_Crossmember
Mirrors
- Rear_Mirror_Bezel
- Rear_Mirror_Bridge
- Rear_Mirror_Support
- Top_Mirror_Bezel
- Top_Mirror_Bridge
Mounts
- Front_Post_Mount
- Side_Post_Mount — print two copies
Posts
- Arduino_Mount
- Arduino_Side_Post
- Front_Post
- Jetson_Side_Post — requires supports
- Jetson_Clip — print three copiesPrinter Requirements
- Build volume: Minimum 256 mm × 256 mm × 256 mm.
- Material: No special filament required—choose your preferred PLA/PETG.
Recommended Print Settings
- Layer height: 0.20 mm (use finer layers on gears/sliders for smoother motion).
- Infill: 20 % baseline (increase for structural components noted below).
- Supports: Not required unless called out.
- Orientation: All STL files are pre-oriented for printing.
Part Checklist by Folder
Use the following checklist to track prints. Notes indicate parts that benefit from finer resolution, higher infill, or support material.
Base
- Base_Plate
- Gear_Rail — finer layer height recommended for smooth motion
- Motor_Mount
- Rail_Slider — finer layer height recommended for smooth motion
- Rear_Base_Mount
- Robo_Base
- Robo_Foot — print four copies
- Ten_Tooth_Gear — print with very fine settings and small layer height
Clamps
- Rear_Projector_Clamp
- Side_Projector_Clamp — print two copies
- Top_Projector_Clamp
Head Frame
- Face_Bezel — increase infill for strength
- Front_Crossmember
- Head_Frame — print two copies; increase infill for strength
- Rear_Crossmember
Mirrors
- Rear_Mirror_Bezel
- Rear_Mirror_Bridge
- Rear_Mirror_Support
- Top_Mirror_Bezel
- Top_Mirror_Bridge
Mounts
- Front_Post_Mount
- Side_Post_Mount — print two copies
Posts
- Arduino_Mount
- Arduino_Side_Post
- Front_Post
- Jetson_Side_Post — Requires supports (Not strict, but would benefit from a high temp material)
- Jetson_Clip — print three copies