1 / 1
Ominous Industries Social Robot
Order a print of this model
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Social Robot from the Bijan Bowen YouTube Channel.
- Rating
- 0 / 5
- Likes
- 0
- Downloads
- 9
- Makes
- 0
- Views
- 114
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- RC & Robotics
- License
- Standard Digital File License
More information about building this can be found here: https://github.com/OminousIndustries/SocialRobot
Here are the printing instructions for all files:
Printer Requirements
- Build volume: Minimum 256 mm × 256 mm × 256 mm.
- Material: No special filament required—choose your preferred PLA/PETG.
Recommended Print Settings
- Layer height: 0.20 mm (use finer layers on gears/sliders for smoother motion).
- Infill: 20 % baseline (increase for structural components noted below).
- Supports: Not required unless called out.
- Orientation: All STL files are pre-oriented for printing.
Part Checklist by Folder
Use the following checklist to track prints. Notes indicate parts that benefit from finer resolution, higher infill, or support material.
Base
- Base_Plate
- Gear_Rail — finer layer height recommended for smooth motion
- Motor_Mount
- Rail_Slider — finer layer height recommended for smooth motion
- Rear_Base_Mount
- Robo_Base
- Robo_Foot — print four copies
- Ten_Tooth_Gear — print with very fine settings and small layer height
Clamps
- Rear_Projector_Clamp
- Side_Projector_Clamp — print two copies
- Top_Projector_Clamp
Head Frame
- Face_Bezel — increase infill for strength
- Front_Crossmember
- Head_Frame — print two copies; increase infill for strength
- Rear_Crossmember
Mirrors
- Rear_Mirror_Bezel
- Rear_Mirror_Bridge
- Rear_Mirror_Support
- Top_Mirror_Bezel
- Top_Mirror_Bridge
Mounts
- Front_Post_Mount
- Side_Post_Mount — print two copies
Posts
- Arduino_Mount
- Arduino_Side_Post
- Front_Post
- Jetson_Side_Post — requires supports
- Jetson_Clip — print three copiesPrinter Requirements
- Build volume: Minimum 256 mm × 256 mm × 256 mm.
- Material: No special filament required—choose your preferred PLA/PETG.
Recommended Print Settings
- Layer height: 0.20 mm (use finer layers on gears/sliders for smoother motion).
- Infill: 20 % baseline (increase for structural components noted below).
- Supports: Not required unless called out.
- Orientation: All STL files are pre-oriented for printing.
Part Checklist by Folder
Use the following checklist to track prints. Notes indicate parts that benefit from finer resolution, higher infill, or support material.
Base
- Base_Plate
- Gear_Rail — finer layer height recommended for smooth motion
- Motor_Mount
- Rail_Slider — finer layer height recommended for smooth motion
- Rear_Base_Mount
- Robo_Base
- Robo_Foot — print four copies
- Ten_Tooth_Gear — print with very fine settings and small layer height
Clamps
- Rear_Projector_Clamp
- Side_Projector_Clamp — print two copies
- Top_Projector_Clamp
Head Frame
- Face_Bezel — increase infill for strength
- Front_Crossmember
- Head_Frame — print two copies; increase infill for strength
- Rear_Crossmember
Mirrors
- Rear_Mirror_Bezel
- Rear_Mirror_Bridge
- Rear_Mirror_Support
- Top_Mirror_Bezel
- Top_Mirror_Bridge
Mounts
- Front_Post_Mount
- Side_Post_Mount — print two copies
Posts
- Arduino_Mount
- Arduino_Side_Post
- Front_Post
- Jetson_Side_Post — Requires supports (Not strict, but would benefit from a high temp material)
- Jetson_Clip — print three copies