1 / 4
HUB75 32x32 LED Matrix Enclosure for MatrixPortal S3 — zdjęcie 1
1 / 4

HUB75 32x32 LED Matrix Enclosure for MatrixPortal S3

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

An enclosure for the 32x32 HUB75 LED matrix with an internal frame supporting the Adafruit MatrixPortal S3

Ocena
0 / 5
Polubienia
8
Pobrania
43
Wydruki
0
Wyświetlenia
414
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

This enclosure was inspired from the Adafruit version that supported a different MCU, but I specifically needed to use the MatrixPortal S3 for WLED-MoonModules compatibility. I also compensated for using 0.75mm thick LCD diffuser plastic within the frame instead of much thicker acrylic.

Word(s) of caution:

Do be warned, both the back lid and outer frame are quite large single pieces, and if you are printing on a smaller printer like me (Prusa Mk4), the edges will almost certainly warp upwards. This absolutely will affect how well the unit fits together. I suppose with some corner brims and/or some gluestick this may work better. A larger printer may help as well. My finished product annoys me because of that, but I don't want to waste filament reprinting since it went together anyways. 

As of the making of this project, vanilla WLED does not support the HUB75 matrices. There is a fork of WLED called WLED-MM which does implement experimental support for the HUB75 protocol. It can be found here: https://github.com/MoonModules/WLED-MM

Flashing it to the MatrixPortal S3 is a bit tricky, but if you follow these steps exactly you will have it working properly.

Finally, I took sandpaper to the outer sides of my matrix to make them completely flush and remove any PCB overhang. This is an important step, as the matrix itself has to effortlessly slide into the internal frame to avoid warping it. Sand both if you need to (I did), but it cannot be anything but perfectly square and flat.

BOM:

  • 1x 32x32 HUB75 LED matrix (https://www.adafruit.com/product/1484)
  • 1x Adafruit MatrixPortal S3 (https://www.adafruit.com/product/5778)
  • 8x M2x6mm countersunk screws (secures inner frame to outer frame)
  • 4x M2x8mm socket cap screws (or similar, for holding the MatrixPortal to the inner frame)
  • 4x M2 washers (for the above screws)
  • 12x M2 3x3.2mm heat set inserts (8x for the outer frame screws, 4x for the MatrixPortal PCB)
  • 1x M3 3x4.2mm heat set insert (for the middle screw of the back panel)
  • 5x M3x30mm countersunk screws (for the back panel)
  • 1x 198x198mm piece of 0.75mm thick diffuser material (or print a rectangle at 100% fill)
    • My diffuser was from an old LCD TV I disassembled

Assembly:

Pretty straightforward:

  1. Insert all heat set inserts into the inner frame and clean up any displaced plastic. The inserts must be flush with no bumps of plastic for proper alignment
  2. Slide the internal frame onto the matrix, with the matrix arrows pointing up and to the right
  3. Screw in the MatrixPortal S3 to the internal frame, making sure its completely flat and tight
  4. Plug in the power connector to the matrix itself and sharply bend the cables down at the connector. I cut and resoldered mine to remove excess length.
  5. Screw in the spade terminals of the power connector to the MatrixPortal S3's screw holes
  6. Plug in the ribbon cable to the matrix and MatrixPortal S3 and fold it flat with an overlapping 90 degree fold on each end. The cable will make a Z shape.
  7. Place the outer frame face down and insert the diffuser into the frame, centering it as best you can
  8. Lay the internal frame and matrix assembly inside, ensuring it is completely flat
  9. Screw in the 8 external M2 countersunk screws in a cross pattern (as if it were a tire) to evenly take up tension
  10. Last, place the rear cover on with the up arrow facing the top of the matrix where its connectors are and screw in place using the M3 countersunk screws

WLED-MM Setup:

Same as normal WLED, just ensure the following otherwise things will look wrong:

Settings > LED Settings 

 

 

 

 

 

 

 

Settings > 2D Configuration

Tagi