1 / 3
Umrandung Bodenöffnung Käfige von Petgard oder Skyline / Floor opening surround for Petgard or Skyline cages — zdjęcie 1
1 / 3

Umrandung Bodenöffnung Käfige von Petgard oder Skyline / Floor opening surround for Petgard or Skyline cages

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A border for the special opening in the floor of Petgard / Skyline cages with two or three levels.

Ocena
0 / 5
Polubienia
0
Pobrania
3
Wydruki
1
Wyświetlenia
38
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Pets
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

— for english please scroll down --

Unser neuer Petgard-Käfig hat zwar ein schönes Loch im Boden. durch das man eine Leiter in die untere Ebene führen kann, aber die Streu fällt da mangels Rand ebenfalls runter - und normale Leitern passen erst recht nicht.

Daher hier eine Umrandung zum Anschrauben. Die Umrandung ist vierteilig, um sie auch auf kleineren Druckern drucken zu können und damit sie nicht bricht, wenn der weiche Kafigboden sich verwindet.

  • Vor dem Drucken bitte vergleichen, ob der Ausschnitt im Käfig paßt (Maße siehe die Datei dim_opening - Maße Öffnung.pdf)
  • Die Teile selbst habe ich aus PLA gedruckt, das wird bei uns nicht angenagt
  • Rund um die Öffnung im Käfig müssen Löcher vorgebohrt werden, siehe Bild. Eine Bohrschablone zum Ausdrucken und Ausschneiden hängt an. Einfach die ausgeschnittene Schablone an der Öffnung ausrichten, mit etwas Klebefilm befestigen und die Löcher bohren.
  • Die Befestigung erfolgt mit 16 kurzen 3mm-Spaxschrauben und passenden DIN 9021-Unterlegscheiben (meine sind für M4-Schrauben). Bei Verwendung dickerer Schrauben die Befestigungslöcher etwas aufbohren.
  • Die beiden großen horizontalen Bohrungen sind dafür ausgelegt, zwei M8-Gewinde zu schneiden und darin Schrauben einzudrehen, in die dann die Leiter eingehängt wird. Alternativ kann man natürlich auch eine passend abgelängte 6mm-Stange reinstecken

-------

Our new Petgard cage has a nice hole in the bottom through which you can insert a ladder to the lower level, but the litter also falls through due to the lack of a rim – and normal ladders don't fit at all.

So here is a rim that can be screwed on. The rim consists of four parts so that it can be printed on smaller printers and so that it does not break if the soft cage floor warps.

  • Before printing, please check that the cut-out fits in the cage (dim_opening - Maße Öffnung.pdf).
  • I printed the parts themselves from PLA, which is not gnawed on here.
  • Holes must be pre-drilled around the opening in the cage, see picture. A drilling template for printing and cutting out is attached. Print it (if you use the A4 variant, glue the two halves together), cut out the inside, carefully align it with the hole in the cage and fix it with a bit of tape. Then drill the holes.
  • The parts are fastened with 16 short Spax screws and matching DIN 9021 washers (mine are for M4 screws). If you use thiocker screws, drill the holes a little wider.
  • The two large horizontal holes are designed to cut two M8 threads and screw in bolts, into which the ladder is then hooked. Alternatively, you can of course insert a suitably cut 6 mm rod.

Tagi