Toyota Prius Gen5 custom in-dash usb module ( 35w max )
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
This is a 35W PD mod for the usb port of Prius ( and possibly other toyota car after 2020 ).
- Ocena
- 0 / 5
- Polubienia
- 2
- Pobrania
- 8
- Wydruki
- 0
- Wyświetlenia
- 195
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Automotive
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Toyota Prius Gen5 have a lot of usb ports, but the usb module it uses only supply 5v@3a max, which is not a common setup that most mobile phone accepts.
This means a lot of phone and tablet will have very bad charging rate when using these in-dash usb ports. I was only able to get 7 watt when I plug my phone into the OEM usb port.
Instead of using a barrel style usb adapter that connects to the 12V out, I opt to retrofit usb module with higher output into the same in-dash usb module form factor. This allows you to swap out the OEM 15w usb module with higher power modules and still keep the clean look. In this mod I swapped in a 65w module ( which will only provide 35w in the 12v max setup in prius. )
=========== DISCLAMER - Modifying your vehicle at your own risk ==========
Modifying your car could void your car warranty, improper electrical connection or faulty parts could cause damage to the electrical system in your car, from blowing fuse to causing fire.
You should not attempt this mod if you do not understand what this mod is meant for, nor should you attempt this if you are not familiar with soldering / knowing what a PD module is / know how to open your car dash to gain access to replace the module
Do this at your own risk!
=========== Parts required ============
- 65w USB Power delivery module
- breakaway dual-male pin header (2.54mm )
- female pin connector x 2
- dupont connector housing - 2p x1
- dupont connector crimp tool. I use this one
- 0.8mm drill bit x 1
- >22awg wire ( I use 18awg), some basic soldering skill
========= Printing and Assemble ========
Print the parts with PETG or ABS, use support as needed. The body should be printed in the model orientation, with the USB port facing down, and you will want to use tree support. The cover should be printed with the perforated flat side on the bed.
After the socket is printed, the hole will likely be too small for the pin header. I use 0.8mm drill to enlarge the hole for a tight fit for the pin header - the tight fit is needed to ensure the friction can hold the header pin firmly in place.
Take 2 header pin and insert into the hole in the socket, push it in so that about 9mm is left outside the tail of the socket.
Carefully insert the socket in to the body until the socket is flush with the body. It should give you a good friction fit.
Next depending on if you are using the single or dual port, solder positive and negative wire to the PD module. try insert the module into the guide track in the body as a dry fit, use this to find out where to cut the wire. you want just enough wire to make the dupont connector and reach the header.
Also ensure you are using wires at least 22awg.. When I try this with 26awg ( outside the car ) the wire went up to 60~70c. I end up manage to fit some 18awg wire into the dupont connector.. that wire barely reach 45c when I draw 3amp for 20 minutes.
Crimp the female dupont connector to the wire, and insert the positive and negative connector into a 2 pin housing. The positive wire should be connect to the left side of the socket, when you are looking from the tail to the socket side. ( do not wire it wrong! While this PD module should have reverse voltage protection, you do not want to test that in your car.. )
after the pd module is connected to the socket, close the cover and use a small screw to secure the cover onto the body.
take apart your center console, remove the old USB module and install the modded one. You should have a USB PD that is capable of charging your phone or tablet at a faster speed now. I was able to charge my phone at ~25w and I am a happy camper.
========= Wattage concern =========
The PD module I choose does not have step up feature, so even though it is a 65w module, with the car providing 12~14v, the max wattage it can at most draw is about 36w at 12v@3a. While not enough for laptop, this should be plenty for most phone and tablet already.
As the fuse for the usb2 is only 10A, and usb2 supplies 4 different usb ports ( 2 in the center console arm rest box, 2 behind the center console for the rear seat ), you should refrain from swapping out all 4 usb port - if you plug them all in and pull 4x3=12A, you run the risk of blowing the fuse. I personally only swap out the 2 under the armrest - that usb is very easy to access, you don't even need any pry tool to get to it.
