DIY 48V DC-Distribution for Victron (Lynx style)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Victron MP2 compatible DC-distribution for 12-60V.
- Ocena
- 5 / 5
- Polubienia
- 34
- Pobrania
- 226
- Wydruki
- 0
- Wyświetlenia
- 1750
- Oceny
- 1
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Electronics
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
This is my try of making a DIY Victron MP2 compatible DC-distribution. It's based of a 40x8mm copper rail which can carry according to DIN EN 61439 1300A. The whole design is inspired by the Victron Lynx but with the requirement of fitting more connections per box and be able to connect cables from top and bottom.
It can fit 6 connections per box and can also include Adler / MEGA fuses, but only exiting one side! The copper bar is one solid connection, avoing the reconnection and complex copper bar shape from the Lynx. I recommend for home use to leave the copper bare and not have them tinned avoiding the growth of dentrites. It can fit Klauke DIN 46235 M8 cable lugs from 25mm2 up to 95mm2 in all directions.
Printing recommendations:
Shown in the picture are 3x MP2 5000, which require 4 sets of housings and two busbars of a length of 976mm.
Housing_bottom: 245mm wide fitting most Bambu und Prusa Printers. Recommended material is PA-GF for the bottom housing (no CF as is MUST be non-conductive). Can be printed without support and regular 0,4mm nozzle. I used Bambu PA6-GF UPDATE: tracked my busbar temps for one year with 3x MP5000 and reached a max of 42°C, so ABS-GF or PC is more than sufficient for most people.
Lid: can be ABS or PC. I used Bambu ABS-GF in matching colors printed on the Prusa Core One. Supports recommended. Could be printed without support, but looks not as nice.
Separators: should be same material as bottom housing
Bridge: should be same material as bottom housing
Touch protection covers: can be same material as lid
connection / end campls: should be same material as bottom housing
Busbar manufacturing:
For manufacturing of the busbars you need a saw to cut the bars to length or order it in the right length, a drill with 4,5mm (5mm also possible) and 8,5mm (9mm also possible) and a screwdriver, that's it. Deburing the edges helps to make it look nice, as well as sandpaper to remove oxidization of the copper. Wearing gloves while handling the busbars is recommended, as otherwise the copper will corrodie within days where you touched it.
I included two drill guides for the busbars. One for marking the plus busbar fitting a cheap amazon automatic centre punch and the other one for the minus busbar. The guides can be made out of cheap PLA.
Start from the left side, using the bottem left opening as an endstop (drill can be inserted)

After makeing all the holes slide the drillguide to the next position, using the most left hole with a drill as a alignment

Material needed:
Bambu PA6-GF
Bambu ABS-GF
Cheap PLA
DIN 933 M8x30 stainless Screw (18x per box)
DIN 125 M8 stainless washer (36x per box)
DIN 934 M8 stainless nut (18x per box)
DIN 127 M8 spring washer (18x per box)
DIN 14583 M4x16 plastic screw (14x per box) Could be any plastix screw. No sheetmetal screw! Prefered 4,5x16 thermoplast.
DIN 439 M8 (low height) nut (6x per box)
Spax 4,5mm screw for srewing it to the wall. Could fit down to 3mm Spax!
Assembly:
Straight forward, just check the picture below. Note: the bigger lug nuts need to be rotate going outside the right side!

Made in SW2021. No commercial use!
UPDATE April 2026:
Included the drawings of the busbars as PDF and theSTEP files of the busbars