K1 Series Build Plate Stopper with Nozzle Cleaning Brush
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Improved build plate stopper for Creality K1 series with a quick-release nozzle cleaning brush slot. Fully parametric
- Ocena
- 5 / 5
- Polubienia
- 17
- Pobrania
- 79
- Wydruki
- 4
- Wyświetlenia
- 553
- Oceny
- 3
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Creality Parts & Upgrades
- Licencja
- Creative Commons — Attribution
⚠ Disclaimer: I am not responsible for any damage or malfunction that may occur to your printer when using this model. Install and use it at your own discretion.
This is a custom build plate stopper designed for Creality K1 / K1C / K1 Max printers.
It replaces the stock stopper bolts with a more precise, convenient, and multifunctional design — featuring a built-in quick-release nozzle cleaning brush that doesn’t attach to the Z-axis rod.
🔧 Key Features
- Improved usability – Easier and more precise plate positioning compared to the stock stopper. No more fumbling with the two tiny bolts!
- Integrated quick-release brush – The nozzle cleaning brush simply slides into a dedicated slot in the stopper. It’s easy to remove or replace — no need to mount anything on the Z-axis.
- Support-free printing – The model is designed to print cleanly without any supports.
- Fully parametric Fusion 360 model –
You can adjust:- Brush size (supports Creality, Bambu Lab, or custom brushes)
- Stopper dimensions (for K1/K1C or K1 Max)
- Brush offset (default: 0.1 mm) – increase it if the brush doesn’t fit, or decrease if it’s too loose.
- Compatible with different build plate types and thicknesses –
The brush is mounted from above, allowing you to use various plate types, including thick glass plates (e.g. 3.9 mm) that would normally interfere with the stock bolt stoppers or Z-axis-mounted brushes.
With this design, nothing bends, and the nozzle is always cleaned properly — even on non-standard plates.
🛠 Fluidd Configuration (K1 / K1C / K1 Max)
If you are using Fluidd, you can manually update the nozzle-cleaning area used by the printer.
These parameters define the exact X/Y start position of the brush and the length of the cleaning pass, so the nozzle wipes across the correct part of the brush.
To configure it:
- Open the Fluidd web interface.
- Go to Configuration → open
printer.cfg. - In the
[prtouch_v2]section, apply one of the following configurations:
K1 / K1C – 38 mm Bambu Lab brush:
clr_noz_start_x: 92
clr_noz_start_y: 226
clr_noz_len_x: 36
clr_noz_len_y: 2K1 / K1C – 50 mm Creality brush (default):
clr_noz_start_x: 87
clr_noz_start_y: 225
clr_noz_len_x: 46
clr_noz_len_y: 1K1 Max – 38 mm Bambu Lab brush (theoretical values, not tested):
clr_noz_start_x: 132
clr_noz_start_y: 303
clr_noz_len_x: 36
clr_noz_len_y: 2
K1 Max – 50 mm Creality brush (default):
clr_noz_start_x: 130
clr_noz_start_y: 303
clr_noz_len_x: 40
clr_noz_len_y: 2🧠 Notes
Installs using the same two top bolts as the stock stopper (just screw them in from below through the new part).
Perfect fit for users who want a clean, modular, and easy-to-maintain nozzle cleaning setup.
For best durability and heat resistance, print this model using ABS or ASA. In extreme cases, you may try PETG, but it has not been tested and is not recommended for long-term use due to possible deformation near high temperatures.