Primo Water Dispenser (hTrio / 601258-C) Dispensing Lock (for hot OR cold side!)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Lock the cold water side of your water dispenser! This is modeled off of the red button that locks the hot water.
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 17
- Wydruki
- 0
- Wyświetlenia
- 468
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other House Equipment
- Licencja
- Creative Commons — Attribution
My toddler has discovered the cold water button in my primo hTrio water dispenser. The hot thankfully comes with a reasonable child-lock. I stumbled upon this reddit thread where they discussed buying a spare hot-side lever and using that to replace the cold side lever. That works great, but then you have two red buttons! I wanted to keep a red and blue button!
Bill of Materials
- A spring (Link TBD)
- This part
Note: If you print this part then you do NOT need to buy a spare lever as discussed in the reddit thread. Just the spring mentioned above.
Printing
I modeled this piece based off the original design, which wasn't exactly meant for 3d printing. As a result the most intuitive print orientation basically means the whole thing needs supports.
- Print with the flat of the locking tab flat on the bed (the STL should import in the right orientation)
- Enable supports (I use grid to make it easier to remove, and organic isn't compatible with variable layer height) - I painted the underside of the button with negative support since removing that might be a pain and its not needed. You can use the 3mf attached to get that automatically.
- PLA/PETG - any material should work
- I used variable layer height to make the button have nicer stairstepping
Onshape Link
https://cad.onshape.com/documents/74c9e9ff079318acb1f0d36b/w/6dc6fe32b9a4ed7fe51390b2/e/3f2bd8e575f6f27b2b15ba56?renderMode=0&uiState=69010c6628e10eff4038e4c8
Install Process
- Remove the single screw holding on the swing door at the bottom of the unit. (I put the whole unit on a table so I could reach underneath it - tipping it over tends to make a mess). You don't actually have to remove the screw, it just backs out maybe a third an inch which lowers a pin in the bottom of the door hinge.
- Remove and the back/top panel – they are one piece held on by 2 screws on the back – near the top of the unit.
- Remove the power connector between the top/back panel and the inner electronics. It'll be obviously the only thing holding the top on.
- Remove the 2 screws off the back of the front panel near the top of the unit.
- Push the front panel downward to release it. (this is why you have to remove the swing door – if the door is still on then the front panel wont move down.)
- The front will hang, held on by water hoses and cables.
- With a short/stubby screwdriver, remove the 6 screws of the lever component. This is fiddly and annoying, but doable. Took me about 15 minutes and some patience. Pro-tip – if your stubby screwdriver is not magnetic, you can attach some of the magnets you might have around your 3d printer workbench to the shaft to make the tip temporarily magnetic to help with those tricky to reach screws.
- Pull out the lever, remove the single screw from the back of the blue plate. Push in the three snap-connectors on the side with a flathead screwdriver and remove the blue plate and blue pushbutton.
- Install the printed push button (with the locking tab) in place of the old push button.
- You can see the hot side fairly easily to reference how it works if necessary.
- Installation is the reverse of the removal.
Photos
Push lever

