"Mojave Breeze" Chamber Heater for Sovol Zero (and others)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Simple chamber heater/carbon filter combo to keep it toasty like the Mojave in your chamber.
- Ocena
- 0 / 5
- Polubienia
- 22
- Pobrania
- 76
- Wydruki
- 0
- Wyświetlenia
- 1274
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Printer Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
NOTICE: USE OF AN AUXILIARY CHAMBER HEATER POSES A RISK TO LIFE AND PROPERTY IF USED INCORRECTLY. BY DOWNLOADING THESE FILES YOU ACKNOWLEDGE THAT YOU ARE AWARE OF THESE RISKS AND AGREE THAT I AM IN NO WAY RESPONSIBLE FOR ANY DAMAGE YOU CAUSE TO YOURSELF, YOUR PRINTER, YOUR DOGS&CATS, YOUR MOM'S BASEMENT, ETC. IF YOU DO NOT UNDERSTAND THIS RISK OR DO NOT FEEL CONFIDENT IN YOUR ABILITY TO USE THIS HEATER SAFELY, DO NOT DOWNLOAD IT.
Printing Note:
Although none of the parts is “structural," per se, you will likely be running this heater between 100-120C and you will need a material that can withstand those temperatures. I recommend some variety of PC (vanilla, PC-CF, ezPC, whatever) as it typically has a HDT in that range. Check the spec sheet for your preferred plastic to ensure it will survive. I have been using this design for more than 250 print hours and have not suffered any material melting or other malfunction with the heater.
BOM:
- 6x Voron Spec Heat Inserts
- 6x M3 screws (any head) ~8mm long
- 24v/100W DC (NOT AC) PTC heater
- GDSTime 7530 blower fan
- Carbon pellets
- NTC100K thermistor
- Heat resistant zip ties
Assembly and Setup:
- Print Body and Lid
- Add heat set inserts (should be obvious where, holes are sized 4.5mm)
- Fill front reservoir with carbon pellets
- Zip tie thermistor to front cage of heater
- Wire heater to a free hotend mosfet on your motherboard (stock Sovol boards and others may not have extras - check first)
- Wire thermistor to free thermistor header on your motherboard
- Config
- Validate safe function and confirm that the fan turns on when the heater goes on. This is essential to not melting the housing.
- Run PID_CALIBRATE for the target temp of your choice. I recommend 100C.
Config:
Be aware that the pins referenced below are specific to my printer and motherboard. DO NOT SIMPLY COPY/PASTE THE BELOW CONFIG. You must check to ensure that you are identifying the correct pins for your system.
[verify_heater chamber_heater]
max_error: 1000
check_gain_time: 1200
hysteresis: 5
heating_gain: 2
[heater_fan chamber_fan]
pin: PA4
max_power: 1.0
cycle_time: 0.015
kick_start_time: 0.5
heater_temp: 35
heater: chamber_heater
heater_temp: 30 #
[heater_generic chamber_heater]
gcode_id: E
heater_pin: PF9
max_power: 1
sensor_type: Generic 3950
sensor_pin: PC5
#pullup_resistor: 20000
control:
pid pid_kp: 32.341
pid_ki: 1.251
pid_kd: 209.001
#max_delta: 1.0
min_temp: 0
max_temp: 200