EGR Solenoid Connector 1980's GM Chevy V8
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Do you have a 1980's GM v8 with an EGR solenoid and need a replacement connector that is now discontinued? Here you go!
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 7
- Wydruki
- 0
- Wyświetlenia
- 44
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Automotive
- Licencja
- Creative Commons — Public Domain
This design is intended to be printed with 100% infill and may be subject to failing with less infill/few perimeters.
Introduction
This replacement connector was designed specifically to fit into the EGR solenoid of a 1986 Chevrolet Monte Carlo SS, but will fit into identical EGR solenoids found on other General Motors products from the same era. On my car, the EGR solenoid valve itself was operational, but the connector in the car's wiring harness was very brittle and falling apart, eventually causing the pins to short and blow the fuse for my ECM. To my dismay, the connectors in my parts vehicles were in no better shape and the connector appears to be discontinued. Luckily, this is where 3D printers come in!
I printed my first connector out of ABS but recommend using a nylon filament instead. ABS has survived several longer drives with the hood opened afterwards to cool the engine bay, but on a hot day or a vehicle with a higher temperature thermostat and poorer engine bay cooling, it may not survive. Therefore, I recommend you print yours out of nylon for the peace of mind, but ABS will get you by in a pinch anyway. I printed a couple more out of PA6 CF which should have no trouble with engine bay temperatures and should survive long-term. I would advise against printing this connector out of any plastic with a lower temperature resistance than ABS.
This connector is 100% 3D printable and requires very little post-processing (removing a small support).
If you are sufficiently happy with how this design has worked out for you, please consider sending a small donation my way if you are able: https://buy.stripe.com/bIY4i488N84rcCY3cc
Notable Printing Considerations
- This is a part subject to high temperatures and vibrations. It is imperative that layer adhesion is very close to perfect, the part has 100% infill, and the plastic used can handle well over 100ºC.
- It is recommended to print the parts out of PA6 CF or some other material that has excellent layer adhesion, strength and temperature resistance.
- If printing with a carbon fiber-filled filament, ensure layer heights do not go below 0.2mm and try to keep a 0.25mm+ layer height where you can to prevent clogged nozzles.
- If printing with a carbon fiber-filled filament, keep in mind the connector may not 100% electrically isolate the two pins of the connector.
- This is a small, detailed part with tight tolerances. It is best to print this slower and with less print defects that could impact the installation of the pins or the connector itself to the EGR solenoid.
Installation
Firstly, check that the connector will fit your car's EGR solenoid before going any further. I can guarantee that they fit properly in mid-1980's carbureted Monte Carlo's, Camaro's, etc. but the solenoid designs did change in later years.
- Remove the supports from the connector after printing. If printing with nylon, you will want to remove the supports before they absorb moisture from the air and become more difficult to remove from the part.

- Ensure the pins that fit in the connector are not damaged or bent. If the locking tab on the pin is bent down too badly, it will not lock in place inside the connector later.
- Insert the pins as shown below with the pink and black wire on the right of the connector. Do not mix up the order of the pins or you may have to destroy the connector to remove the wires.

- Ensure the pins are fully inserted and seated. They should clip into place inside the connector and be firmly seated, unable to be pulled out and removed.

- Install your new connector on the EGR solenoid.

