1 / 6
WIP Magnetic Swirl Mask & Front Aperture System for Helios 44-2 — zdjęcie 1
1 / 6

WIP Magnetic Swirl Mask & Front Aperture System for Helios 44-2

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Magnetic, non-destructive front clamp system for the Helios 44-2. Allows quick swapping of front-mounted aperture plates

Ocena
0 / 5
Polubienia
1
Pobrania
10
Wydruki
0
Wyświetlenia
126
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Photo & Video
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

This project is a magnetic, non-destructive front clamp system for the Helios 44-2, designed to hold interchangeable front aperture plates and swirl / bokeh masks.
All parts are fully 3D printable and the system requires no permanent modification to the lens.

The design uses embedded neodymium magnets to allow fast, repeatable snap-on mounting of different optical plates while keeping alignment consistent.


The system consists of two main component types:

Magnetic Lens Clamp Ring

This is the main clamp that mounts onto the front of the lens and provides the magnetic interface.

  • Clamps around the lens front using a tightening screw

  • Houses embedded magnets for attaching optical plates

  • Non-marring and fully reversible

Magnetic Optical Plates

Interchangeable snap-on plates that attach magnetically to the clamp ring.

Examples:

  • Fixed front aperture plates

  • Swirl / bokeh enhancement masks

  • Experimental pupil masks

Each plate uses matching magnets to ensure proper alignment and a secure snap fit.


For the Magnetic Lens Clamp Ring

  • 3 × Neodymium magnets

    • Ø8 mm diameter

    • 1.7 mm thickness

  • 1 × Heat-set threaded insert

    • For M3 screw

  • 1 × M3 bolt

    • Length: long enough to reach from the thin clamp tab into the threaded insert in the thicker clamp body

  • CA glue (cyanoacrylate / super glue)

Assembly notes

  • Glue each magnet into its dedicated slot using one small drop of CA glue

  • Pay close attention to magnet polarity

    • All three magnets must be oriented the same way

    • Test-fit against a plate magnet before gluing

  • Install the heat-set insert according to the filament manufacturer’s temperature recommendations


For Each Magnetic Optical Plate

  • 3 × Neodymium magnets

    • Ø8 mm diameter

    • 1.7 mm thickness

  • CA glue (cyanoacrylate / super glue)

Assembly notes

  • Glue magnets into the plate using a small drop of CA glue per magnet

  • Magnet polarity is critical

    • Ensure the plate magnets attract (not repel) the magnets in the clamp ring

    • Dry-fit and mark orientation before gluing


Recommended

The Magnetic Lens Clamp Ring should be printed in a slightly flexible material to allow safe clamping without stressing the lens:

  • PETG (recommended)

  • ABS

  • Nylon

Not recommended

Avoid stiff or brittle filaments for the clamp ring:

  • PLA

  • Carbon fiber–filled filaments

  • Glass fiber–filled filaments

These materials are too rigid and may:

  • crack during clamping

  • fail to grip evenly

  • risk cosmetic damage to the lens

Optical plates can be printed in stiffer materials if desired, but matte black filament is recommended to reduce internal reflections.


Notes & Tips

  • Blackening the inside surfaces (marker or matte paint) can further reduce reflections

  • Always test magnet orientation before gluing

  • The system is designed for experimentation, feel free to design your own plates using the same magnetic interface

Tagi