openGrid Standard 90 Degree Angled Conenctors (Remixed from KYZ Design Angled Connectors)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Orientacyjna cena wydruku pliku
2,69 € – 3,29 € netto (bez VAT)
Dla pliku: Print All PLA with PLA Supports.bgcode
To wstępna wycena jednego pliku. Dokładną cenę poznasz przed zamówieniem.
Plik i założenia wyceny
Plik użyty do wyceny
Średnia wycena orientacyjna: 2,99 € netto (środek widełek).
- Masa podana przez autora
- 41 g
- Czas druku podany przez autora
- 2,82 godz.
- Materiał u źródła
- PLA
- Materiał wyceny
- PLA
- Drukarka wyceny
- Bambu Lab P1S - 0.4 nozzle
- Proces wyceny
- 0.20mm Standard
Orientacyjna wycena wyłącznie wybranego pliku, oparta na masie i czasie druku podanych przez autora. Warianty plików nie są sumowane. Ostateczna cena zostanie obliczona po analizie pliku.
Zapisane na tym urządzeniu.
Three 90 degree angled connectors remixed from KYZ Design's to align with standard openGrid instead of openGrid heavy.
- Ocena
- 0 / 5
- Polubienia
- 20
- Pobrania
- 108
- Wydruki
- 0
- Wyświetlenia
- 628
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Organizers
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Two-way and three-way 90 degree connectors for openGrid regular/standard, based on the designs by KYZ Design (see remix links). Original angled snap-in connectors were aligned for use with openGrid heavy, and while they do work with regular/standard openGrid base plates, they are misaligned when using on regular/standard openGrid. These have been tweaked to support regular openGrid plates and keep them properly aligned. I also made a three-way connector for use on corners!
For printing:
Two-way 90 degree (type 1 and 2) angled snaps can be printed without supports when laying on their sides. Don't forget to print four rings as well and insert them into the slots when the print is finished. See photos for details. Print four rings per connector.
Three-way 90 degree angled snap needs supports for the ring slots, and also for the center of the underside if you want that to look clean. It works well with regular breakaway supports, but even better with soluable supports or incompatible material supports. I printed the main body out of PLA and used some low-grade PETG for supports (see photos). It also may print without supports, but I did not try. Make sure object is angled as shown in photos! Print six rings per connector.
Rings can be printed flat on the build plate. Print and press-fit into the connector slots.
General Print Settings: PLA, 0.20 mm layer height, two perimeter walls, 15% infill. PETG will also probably work but I have not tried that yet.
I have also included the FreeCAD design files as well as the STEP files for others to use. I only do occasional CAD work and the there may be some bad design decisions. Remix at own risk! Additionally, KYZ Design also published connectors at angles other than 90 degrees if someone wants to remix those into the correct alignment for regular/standard openGrid!
A big shoutout to KYZ Design's snap connectors; they are amazing! If you are using openGrid Heavy, I highly recommend the original designs they produced as they are properly aligned for oG Heavy. As credit to KYZ for the inspiration, I have left their mark on the connectors.