Yaesu FTM-500 FTM-510 AMPS mount
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Adapter to mount Yaesu FTM 5xx series to a quick release with an AMPS pattern. Includes anti-rotation provision.
- Ocena
- 0 / 5
- Polubienia
- 2
- Pobrania
- 23
- Wydruki
- 1
- Wyświetlenia
- 315
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Gadgets
- Licencja
- Creative Commons — Attribution — Share Alike
This will adapt a Yaesu FTM-510 or FTM-500 to a standard 38x30 AMPS mount using a 5mm stud. Or any other radio that uses a 5mm stud.
It is designed to work with a quick release adapter that attaches to the device, rather than screw directly to an AMPS mount. I designed it specifically to work with ProClip part #215053 and the included screws (the screws just barely thread into the nuts as designed). This is a parameterized openscad model so you should be able to adapt it to other mounts or screw sizes pretty easily without a lot of work.
Bill of Materials
In addition to the printed model, radio, and mount, you will need:
An M5x0.8x10mm bolt for the radio mounting stud. The head should not be more than 4.8mm tall (most bolts should meet this criteria). You will not be cranking this fastener down hard so you can usually file the head a little bit if it's too tall.
A single M5 or 1/4" washer under the stud is optional but recommended (the thickness of washer counts against the max height of the bolt head)
4x M4 nuts, with a flat-to-flat external dimension of 6.76mm (.266")
Model Selection
There are 4 models here:
amps - This is generic flat AMPS mount with no anti-rotation provisions. It should print easily on any printer. An M4 bolt works great for pushing the supports out. The downside to this mount is the stud may loosen if the radio is bumped around too much. This model is also a good choice for anything non-Yaesu that uses a 5mm stud.
amps-hirth - This is the same mount as above, but with the teeth ("hirth joint") for anti-rotation built into the mount. These seem to print OK at 0.2mm (they don't look good but they work). Consider printing the insert for the other model first to confirm your printer does a reasonable job on the hirth joint.
amps-hirth-needs-insert - Recommended. Same as above mount but you print the hirth joint separately as an insert. Use this if you need to print the hirth joint with different settings to get decent results (that way you can avoid printing the entire part at an annoyingly small layer height).
hirth-insert-only - the insert. Seems to print OK at 0.2mm on a Voron 0.2 even if it doesn't look good. I tried at 0.12mm and it looked worse but seemed functionally the same. This is also useful to see how well your printer does with the hirth joint before taking the time and material to print the mount with the integrated joint.
Unfortunately for all of the mounts with a hirth joint, they will not allow "live" repositioning of the radio. You will have to remove the quick-release adapter to loosen the stud and adjust the position. But it will stay once you've got it right!
I recommend the mount with the integrated hirth joint because fitting the insert can be a pain and sometimes there will still be a little bit of play where the insert fits into the mount.
The hirth joint is 40 teeth, 20mm outer diameter, 8mm inner diameter. This can also be adjusted in the model(s) if you want to use it with equipment that uses a different pattern.
Print settings
print in default orientation
use supports (not required for insert-only)
40% infill (I used cubic)
0.2mm layer height
4 walls
5 top/bottom layers
Assembly
Push the nuts all the way into the holes. I thread them onto a long bolt and use that to push them in. It's a tight fit--adjust the model if you can't get them in. You could also use a longer bolt with a washer on the outside to "pull" the nuts into the holes.
Assemble the hirth joint insert into the mount if you printed them separately. Depending on your printer you might have to do some shaving and and fitting. Maybe use a drop of superglue to hold them together.
Consider using a washer under the bolt head on the back (opposite the radio) side of the mount. But make sure the bolt isn't sitting above the pocket or it will hit whatever you're attaching to the mount.
Insert the bolt and start threading into the radio (but not so far the teeth engage). Orient the radio where you want it and finish tightening the bolt.
Attach the quick-release bracket to the back of the mount by threading the screws into the captured nuts you installed in the mount earlier. On the ProClip mount the screws only engage a couple turns--they will not quite thread all the way into the nuts.
Editing
OpenSCAD is free and open source. I have parameterized the major elements so it should be pretty easy to adjust things like hole size without and CAD or openSCAD knowledge.
Because of the hirth joint, there are three dependencies that must be installed in order to render the model and generate a new STL:
https://github.com/GillesBouissac/agentscad/wiki/Prerequisites
Licensing/Attribution
This project is licensed under CC BY-SA 4.0. https://creativecommons.org/licenses/by-sa/4.0/
I am using openscad code from DaveX's "OpenSCAD configurable Hirth joints" to generate the Hirth joints:
https://www.thingiverse.com/thing:3838407
Additional license notices from dependencies used to generate the STLs
agentscad
/*
* Copyright (c) 2019, Gilles Bouissac
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
* * Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
* * Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
*
* Description: Hirth Joint modelisation
* Author: Gilles Bouissac
*/
scad-utils
Copyright (c) 2014 Oskar Linde
Permission is hereby granted, free of charge, to any person obtaining a copy
of this software and associated documentation files (the "Software"), to deal
in the Software without restriction, including without limitation the rights
to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
copies of the Software, and to permit persons to whom the Software is
furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all
copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.