1 / 4
250mm Marble-Bearing Lazy Susan (Smooth, Low-Profile, Printable Turntable) — zdjęcie 1
1 / 4

250mm Marble-Bearing Lazy Susan (Smooth, Low-Profile, Printable Turntable)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

250mm low-profile Lazy Susan using 14mm marbles instead of bearings. Optional rim included.

Ocena
0 / 5
Polubienia
3
Pobrania
19
Wydruki
0
Wyświetlenia
139
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Kitchen
Licencja
Creative Commons — Attribution

This is a 250 mm (≈10") low-profile Lazy Susan that uses standard 14 mm marbles as the bearing surface for smooth, quiet rotation — no specialty bearing rings required.

The design captures 45 marbles between printed races to distribute load evenly and provide stable, fluid motion. Glass marbles are recommended because they’re inexpensive, easy to find, and more than sufficient for this application.

An optional rim can be added to keep items contained, making it ideal for seasonings, condiments, or tabletop organizers. Leave the rim off for a flat, unobstructed surface, perfect for cake decorating or display use.

The exploded and cross-section views illustrate:

  • Blue → printed parts

  • Transparent cyan → marbles

  • Gray → screws & washer

  • Orange → heat-set insert

  • Yellow → assembly/alignment lines


🧩 Features

  • ✔ Uses inexpensive 14 mm marbles (glass recommended)

  • ✔ Optional rim for containment or spill prevention

  • ✔ Smooth rotation with wide load distribution

  • ✔ Minimal hardware

  • ✔ Forgiving tolerances — works well across printers

  • ✔ Minimal Supports — just one spot on one part.


📐 Specifications

  • Overall diameter: 250 mm

  • Plate height: ~30 mm

  • Rim height (optional): ~25+ mm additional

  • Bearing type: Captured loose marbles

  • Marble count: 45

  • Marble size: 14 mm diameter


🧰 Hardware Required

With Rim Installed

  • 45 × 14 mm marbles (glass recommended; any material works if size is correct)

  • 7 × M3 screws

    • Length: 10–25 mm (use what you have)

  • 1 × M3 washer

  • 1 × M3 heat-set insert

Without Rim (Flat Plate Only)

  • 45 × 14 mm marbles

  • 1 × M3 screw (10–25 mm)

  • 1 × M3 washer

  • 1 × M3 heat-set insert


🖨 Printing Recommendations

  • Material: Anything Rigid (PLA, PETG, ABS, etc.)

  • Layer height: 0.2 mm recommended

  • Infill: 15–25%

  • Perimeters: 3+

  • Supports:

    • A small amount of support is needed under the inner flat of the recessed screw hole of the plate part.

    • This keeps the screw head flush so the top surface remains smooth and uninterrupted

Supports are minimal and easy to remove.


🔧 Assembly Overview

  1. Install the heat-set insert (location shown in orange)

  2. Place 45 marbles evenly into the bearing channel

  3. Align plate and base

  4. Secure with the required number of screws (1 without rim, 7 with rim)

  5. Adjust screw tension slightly to fine-tune rotation

Avoid overtightening — the marbles should roll freely.


⚠ Notes

  • Glass marbles are ideal: cheap, smooth, and readily available

  • Metal ball bearings: relatively inexpensive and smooth, but heavy.

  • Printed marbles can work but will roll rough and are not recommended

  • Any marble material is acceptable as long as the diameter is 14 mm, the surface is smooth, and the material is relatively durable.

Tagi