1 / 4
Toyota Prado Rear-Door Water Tank — zdjęcie 1
1 / 4

Toyota Prado Rear-Door Water Tank

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Slim water tank designed to fit inside the Toyota Prado rear door cavity.

Ocena
0 / 5
Polubienia
7
Pobrania
27
Wydruki
0
Wyświetlenia
317
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Automotive
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

This is a slim water tank I designed to fit inside the Toyota Prado rear door cavity. It can be used to store non-drinking water and used for handwashing, cleaning, etc.

It should fit on any J150 Prado (roughly 2009–2023) if the rear door inner panel is the same; mine is a 2015 GX-R.

Tap outlet choice:
The design has an optional threaded end. If you have a tap that fits the threads, then that's perfect. Otherwise, you can use the same hole for whatever tap you find. You can also edit the STL to remove the threads, of course. I initially used a threaded jerry-can-style tap, which ended up being very leaky, so I switched to a garden hose-style tap, which luckily fit in the same hole and worked much better.

Credit goes to https://www.thingiverse.com/thing:3238736/makes for the thread and cap design.

Instructions:

1) Materials & Hardware:
  • Recommended filament: ABS

  • Hardware:

    1. Tap/spigot (Jerrycan-style tap or garden/hose quick-connect tap, test the tap first, some taps leak even when “off”)

    2. O-ring (highly recommended for the tap)

    3. RTV silicone sealant. If you want potable water, use food-safe silicone and food-safe plastic.

  • Tools:

    1. Sandpaper (80–220 grit)

    2. Pure acetone

    3. Small brush (for slurry) / disposable brush

    4. PTFE tape (for threaded connections, optional)

    5. Gloves + eye protection + good ventilation

2) Print Settings (ABS)

These settings are aimed at watertight prints:

  • Layer height: 0.2 mm (I used 0.3, but lower creates a better seal)

  • Perimeters/Walls: I only used 2 shells, but I did get some leaks so more should be better

  • Top/Bottom layers: I had mine at 0.6mm

  • Infill: 15–30%

  • Make sure you set your filament diameter correctly (if you set the diameter too big: under-extrusion, weak layers, gaps, leaks)

3) Printing the STLs
  1. Print each segment

  2. Then solvent-welds the seams (see next section)

4) Assembly: Joining Sections (Solvent Welding)

You will need ABS Slurry (strong + gap-filling): dissolve ABS bits in acetone until it forms a thick paste. You can watch a YouTube video on how to make it; it's very simple.
How to use it:

  1. Lightly sand mating edges and prep the surfaces with alcohol to remove any leftover grease/dirt.

  2. Brush a thin layer of slurry on one face (and/or both).

  3. Quickly press pieces together tightly (don't give the slurry enough time to dry; the fit is already very tight)

  4. Paint some more ABS slurry onto the inside and outside of the seams. You will only have the chance to apply ABS slurry to the inside of the seams once, as it will no longer be possible to reach the inside once you put all the pieces together. So be generous.

  5. Clamp/strap tightly and leave undisturbed while it bonds.
    Cure time:
    Handling strength: often within hours
    Leak testing/stress: wait at least 24 hours (longer is safer)

5) Leak Testing
  1. Fill the tank with water (start at ~25–50% first, then fill to full).

  2. Dry the outside completely.

  3. Place it on dry cardboard/paper towels and wait 30–60 minutes.

  4. Rotate to different orientations (so every seam sees pressure).

  5. Do an overnight leak test to detect tiny leaks.

  6. Mark leaks with a pen, drain, dry, and apply more slurry to those areas.
    I had minimal leaks from 2 seams, so I applied more slurry to those areas and waited another 24 hours. Didn't have any leaks after that.

6) Optional: Acetone Vapor Smoothing (Cosmetic / Minor sealing)

This is optional. It will give your tank a glossy look. If your tank passes leak tests and you don’t care about cosmetics, you can skip it, as there is a risk of warping/ruining the tank if done incorrectly. I couldn't find a container big enough to fit the tank, so I skipped this part.
If you do it:

  • Do it outdoors ideally

  • No flames / no sparks (acetone vapor is flammable)

  • Keep it short and check frequently — too much can soften/warp parts
    Note: Vapor smoothing can improve surface finish, but it’s not a magic fix for bad layer bonding or major leaks. Slurry + good print settings matter more.

7) Tap Installation:
  • This is where I struggled the most with leaks, so do this carefully.

    1. Ensure the tap hole area is clean and flat.

    2. Use an O-ring between the tap flange and the tank wall.

    3. Add a thin bead of RTV silicone around the interface.

    4. Tighten snugly — don’t overtighten and crack the print.
      Silicone cure: 24–48 hours minimum (longer if thick).

  • If you’re using threads

    1. PTFE tape can help with thread sealing, but it won’t fix poor mating surfaces.

    2. The seal should ideally come from an O-ring / gasket, not just a thread.

1-Month Update (real use)

  • After about a month, I noticed water could seep out of the cap area when driving (sloshing), especially from the small vent hole.

  • Fix #1: I added an O-ring inside the top cap to improve the seal.

  • Fix #2: I covered the vent hole with a flip-top / push-pull bottle spout (like on sanitizer/sports bottles) so it can be opened for venting and closed while driving to stop splashes.

Hope ya'll like it!

Tagi