Deadlaus Mod (QIDI Q1 Pro)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Deadlaus Mod is a toolhead-focused upgrade for QIDI Q1 Pro aimed at reliable high-temp, enclosed, technical printing.
- Ocena
- 5 / 5
- Polubienia
- 12
- Pobrania
- 30
- Wydruki
- 1
- Wyświetlenia
- 426
- Oceny
- 1
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Printer Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Deadlaus Mod is a toolhead-focused upgrade for the QIDI Q1 Pro, aimed at reliable high-temperature, enclosed, technical printing.
It adds a Klicky-style detachable probe, moves the hotend to the Volcano nozzle ecosystem (incl. CHT inserts), upgrades hotend cooling and part cooling, and adds an extra rear-cover fan to reduce heat soak in a hot chamber.
Fully reversible to stock (no permanent mods required — you can return to the original toolhead setup).
Highlights
Klicky detachable probe for accurate Z and flexible build surfaces
Volcano nozzle system (supports CHT inserts) for higher flow and stronger parts
Upgraded hotend cooling fan to 3010
Upgraded part cooling duct
Added rear-cover fan to prevent toolhead overheating in a hot chamber
Designed for enclosed engineering materials workflow
Detachable front cover thanks to a pogo-pin connection for the part cooling fan
Rear electronics exhaust fan relocated to the back wall to pull hot air away from the electronics bay and improve temperature stability in enclosed setups
Deterministic XY motion tuning (StealthChop disabled) for more repeatable high-speed moves and cleaner motion behavior
Reversible mod: can be restored back to stock configuration
Pros
Proven hot-chamber readiness: stable printing at 80°C chamber (tested), likely higher depending on your setup
Works on basically any build surface (including glass) thanks to Klicky probing and consistent Z referencing
Stronger parts / higher throughput using Volcano nozzles + CHT inserts (more flow headroom, better layer bonding at speed)
Toolhead stays cooler in an enclosed printer: rear-cover fan reduces heat soak and helps protect electronics
More repeatable first layer after maintenance: detachable probe reduces “drift” from fixed sensors
More repeatable motion at high accel: XY drivers run in a consistent regime (no StealthChop), improving torque consistency for aggressive CoreXY profiles (at the cost of extra motor noise)
Cons
Harder extruder access: servicing the extruder or clearing clogs takes longer due to the toolhead layout and added parts
Slightly reduced printable area near the Klicky dock zone (rear notch). Keep models out of that region to avoid collisions
More noise (by design): X/Y run in a consistent non-StealthChop regime for repeatability at high accel + extra fans add airflow noise
You can reduce noise by lowering accel/jerk, reducing fan speeds, or enabling StealthChop below a speed threshold (if you accept less deterministic motion)
Reduced maximum Z height: using a ~5 mm glass build plate and longer Volcano nozzle setups can slightly reduce available Z travel
No automatic nozzle wipe/cleaning: use a manual wipe/brush or a purge line in your start G-code
Part cooling asymmetry: even though the duct is designed for balanced flow, one side may cool slightly better due to outlet geometry
Disclaimer
This is not a beginner mod. You should be comfortable with disassembly, wiring, tuning, and Klipper configuration. Expect to recalibrate after installation (Z offset, probing workflow, temperatures/flow, PA, cooling, etc.).
Use at your own risk: everything is provided as-is. The author assumes no responsibility for any damage, malfunction, injury, or loss.
BOM (Bill of Materials)
Main fasteners
Self-tapping screws, hex socket M3×8 (outside duct → front cover)
Self-tapping screw, hex socket M2.6×6 (inside duct → front cover)
Screws, hex socket M3×16 (rear/chamber fan → printer back wall)
Flat head screws, hex socket M2.5×6 (extruder fan duct → radiator/heatsink)
Flat head screws, hex socket M2.5×16 (3010 extruder fan → extruder fan duct)
Heat-set inserts M3 (blower fan, rear/chamber fan mounts, etc.)
Fans
Electrical / contacts
Klicky standard hardware
Hardware
Tools
Standard hex keys
Printing recommendations
I recommend print all parts from PC-CF material. It has one of the best heat resistance and little creeping. Use minimum part fan cooling possible to achieve better layer adhesion. All models optimized for 0.2 layer height.
Final tuning
After printing and installing all parts, replace your printer.cfg with the new one (see the latest version on GitHub).
Because every printer is a bit different, verify Klicky docking/undocking before doing full homing:
Manually move the toolhead by hand (motors disabled) and confirm the Klicky can dock and undock without binding.
Run G28 X Y.
Using the coordinates in printer.cfg, move to the Approach point first, then creep toward the Dock point in small steps. Dock/undock a few times to confirm it’s reliable.
If docking/undocking is stable, run a full G28.
After that, recalibrate as needed:
PID_CALIBRATE (hotend, chamber and bed) — do this with the chamber and bed heated to your typical printing temps
Belt tension check/adjust
PROBE_CALIBRATE / Z offset
SHAPER_CALIBRATE
SCREWS_TILT_CALCULATE
Bed mesh calibration
Optional: X/Y rotation distance (steps/mm)
I recommend doing all calibration with the chamber heated to your typical printing temperature (including belt tension).
Note: Avoid relying on SAVE_CONFIG if it is unstable on your setup. Instead, copy the final calibrated values into the correct sections of the config manually.
More detailed step-by-step instructions are available on Boosty (soon) and Patreon.
Additional required projects (find on Printables)
Qidi Q1 Pro Rear TPU Seal
Qidi Q1 Pro Heat Loss Plugs
Qidi Q1 Pro Riser
Qidi Q1 Pro Belt Tension block
Tags:
qidi, qidi-q1-pro, q1-pro, toolhead, mod, upgrade, klipper, klicky, detachable-probe, volcano, cht, high-temperature, enclosed, pc-cf, abs, asa, nylon, pa-cf, cooling-duct, fan-duct, pogo-pins, corexy