1 / 5
Deadlaus Mod (QIDI Q1 Pro) — image 1
1 / 5

Deadlaus Mod (QIDI Q1 Pro)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Deadlaus Mod is a toolhead-focused upgrade for QIDI Q1 Pro aimed at reliable high-temp, enclosed, technical printing.

Rating
5 / 5
Likes
14
Downloads
30
Makes
1
Views
434
Reviews
1

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial — Share Alike

Deadlaus Mod is a toolhead-focused upgrade for the QIDI Q1 Pro, aimed at reliable high-temperature, enclosed, technical printing.

It adds a Klicky-style detachable probe, moves the hotend to the Volcano nozzle ecosystem (incl. CHT inserts), upgrades hotend cooling and part cooling, and adds an extra rear-cover fan to reduce heat soak in a hot chamber.

Fully reversible to stock (no permanent mods required — you can return to the original toolhead setup).

Highlights

  • Klicky detachable probe for accurate Z and flexible build surfaces

  • Volcano nozzle system (supports CHT inserts) for higher flow and stronger parts

  • Upgraded hotend cooling fan to 3010

  • Upgraded part cooling duct

  • Added rear-cover fan to prevent toolhead overheating in a hot chamber

  • Designed for enclosed engineering materials workflow

  • Detachable front cover thanks to a pogo-pin connection for the part cooling fan

  • Rear electronics exhaust fan relocated to the back wall to pull hot air away from the electronics bay and improve temperature stability in enclosed setups

  • Deterministic XY motion tuning (StealthChop disabled) for more repeatable high-speed moves and cleaner motion behavior

  • Reversible mod: can be restored back to stock configuration

Pros

  • Proven hot-chamber readiness: stable printing at 80°C chamber (tested), likely higher depending on your setup

  • Works on basically any build surface (including glass) thanks to Klicky probing and consistent Z referencing

  • Stronger parts / higher throughput using Volcano nozzles + CHT inserts (more flow headroom, better layer bonding at speed)

  • Toolhead stays cooler in an enclosed printer: rear-cover fan reduces heat soak and helps protect electronics

  • More repeatable first layer after maintenance: detachable probe reduces “drift” from fixed sensors

  • More repeatable motion at high accel: XY drivers run in a consistent regime (no StealthChop), improving torque consistency for aggressive CoreXY profiles (at the cost of extra motor noise)

Cons

  • Harder extruder access: servicing the extruder or clearing clogs takes longer due to the toolhead layout and added parts

  • Slightly reduced printable area near the Klicky dock zone (rear notch). Keep models out of that region to avoid collisions

  • More noise (by design): X/Y run in a consistent non-StealthChop regime for repeatability at high accel + extra fans add airflow noise

    • You can reduce noise by lowering accel/jerk, reducing fan speeds, or enabling StealthChop below a speed threshold (if you accept less deterministic motion)

  • Reduced maximum Z height: using a ~5 mm glass build plate and longer Volcano nozzle setups can slightly reduce available Z travel

  • No automatic nozzle wipe/cleaning: use a manual wipe/brush or a purge line in your start G-code

  • Part cooling asymmetry: even though the duct is designed for balanced flow, one side may cool slightly better due to outlet geometry

Disclaimer

This is not a beginner mod. You should be comfortable with disassembly, wiring, tuning, and Klipper configuration. Expect to recalibrate after installation (Z offset, probing workflow, temperatures/flow, PA, cooling, etc.).

Use at your own risk: everything is provided as-is. The author assumes no responsibility for any damage, malfunction, injury, or loss.

BOM (Bill of Materials)

Main fasteners

Fans

Electrical / contacts

Klicky standard hardware

Hardware

Tools

Printing recommendations

I recommend print all parts from PC-CF material. It has one of the best heat resistance and little creeping. Use minimum part fan cooling possible to achieve better layer adhesion. All models optimized for 0.2 layer height.

Final tuning 

After printing and installing all parts, replace your printer.cfg with the new one (see the latest version on GitHub).

Because every printer is a bit different, verify Klicky docking/undocking before doing full homing:

  • Manually move the toolhead by hand (motors disabled) and confirm the Klicky can dock and undock without binding.

  • Run G28 X Y.

  • Using the coordinates in printer.cfg, move to the Approach point first, then creep toward the Dock point in small steps. Dock/undock a few times to confirm it’s reliable.

  • If docking/undocking is stable, run a full G28.

After that, recalibrate as needed:

  • PID_CALIBRATE (hotend, chamber and bed) — do this with the chamber and bed heated to your typical printing temps

  • Belt tension check/adjust

  • PROBE_CALIBRATE / Z offset

  • SHAPER_CALIBRATE

  • SCREWS_TILT_CALCULATE

  • Bed mesh calibration

  • Optional: X/Y rotation distance (steps/mm)

I recommend doing all calibration with the chamber heated to your typical printing temperature (including belt tension).

Note: Avoid relying on SAVE_CONFIG if it is unstable on your setup. Instead, copy the final calibrated values into the correct sections of the config manually.

More detailed step-by-step instructions are available on Boosty (soon) and Patreon.

Additional required projects (find on Printables)

  • Qidi Q1 Pro Rear TPU Seal

  • Qidi Q1 Pro Heat Loss Plugs

  • Qidi Q1 Pro Riser

  • Qidi Q1 Pro Belt Tension block

Tags:

qidi, qidi-q1-pro, q1-pro, toolhead, mod, upgrade, klipper, klicky, detachable-probe, volcano, cht, high-temperature, enclosed, pc-cf, abs, asa, nylon, pa-cf, cooling-duct, fan-duct, pogo-pins, corexy

Tags