1 / 9
Betaflight Pavo20 - DJI O4 Pro + GPS canopy — zdjęcie 1
1 / 9

Betaflight Pavo20 - DJI O4 Pro + GPS canopy

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Remix model with mounting for Pavo20 and Pavo 20 Pro wheelbase with Nano-GPS Holder

Ocena
0 / 5
Polubienia
15
Pobrania
78
Wydruki
0
Wyświetlenia
546
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
RC & Robotics
Licencja
Creative Commons — Attribution — Share Alike

I remixed the awesome canopy by "ananasio" to be compatible with the standard Pavo20 and Pavo20Pro airframe.
I have added screw holes to secure the O4 Pro main unit to the frame as a precaution. (That thing was expensive...)
I have also included the Flywoo GOKU GM10 Nano V3 GPS w/compass into the design.

I have yet to test the GPS chip.
I don't know if the Reception is sufficient.
(Edit 10 satellites locked after 2min wait, seems about right)

Additional hardware needed:
4 x M2x3 heat inserts
4 x M2x4 screws
If you want to use the GPS holder you need additionally:
2 x M2x3 heat inserts
2 x M2x4 screws

The rest can be installed using the OEM hardware.

Print Settings

  • Printer brand: Creality

  • Printer: K1

  • Rafts: Doesn't Matter

  • Supports: Yes

  • Resolution: 0,2mm

  • Infill: 20% and up

  • Notes: Best to use 3 or more perimeters
    Material: Overture PETG; 80°C Bed
    255°C Nozzle
    9mm³/s (Limiting my 250mm/s default speed)
    manual tree support for overhangs

Post-Printing

Step 0: Preperation of the electronics

Part selection :
Flywoo GOKU GM10 Nano V3 GPS w/compass
I have chosen this GPS chip for its size and performance as tested by https://oscarliang.com/gps-review/
In addition to that I chose to get the version with the integrated compass as it features a pluggable connection cable. This simplifies the assembly significantly.

The GPS is controlled via UART while the compass can be reached by a i²c port, of which there are none available on the Pavo20s stock F4 2-3S 20A AIO FC V1.
(The STM controllers UART3 pins can be setup as a i²c port. That requires the installation of a modified firmware. But I am not willing to mess with this as I do not need the compass in my build)
You can just leave the SCL and SDA wires not connected or carefully cut them off
In my case I wound up the two unused wires in a way that the open ends do not touch and secured them with a piece of heat shrink tubing.

Connection and Setup:
(See https://betafpv.com/products/f4-2-3s-20a-aio-fc-v1 for reference)
The PCB is mounted in such a way, that its TOP side will be facing downwards.
I used UART1 as well as the 5V and GND pads next to T1 and R1 to connect the GPS module to the FC.
Try increasing the soldering irons temperature a bit for connecting GND as this power terminal dissipates a lot of heat.
(And flux is a friend here, just remove any residue with for example isopropanol)

At this point I advise on using a "Smoke Stopper" for the first power up after any modification to the drone!
It saved my Pavo20 because I did not notice a piece of wire cutting trapped between the power pads.

Before assembling check the connection by setting up the GPS module.

Basic Betaflight Setup
If you chose too follow my build than you need to set up the GPS module like this inside of for example betaflight:

  1. Ports Menu Enable UART1 "Sensor Input" column with "GPS" and 115200 Baud

  2. Save and reboot

  3. Configuration Menu enable GPS iin "Other Features"

  4. Save and Reboot

  5. GPS Menu UBLOX Protocol; Auto Config enabeled; Use Galileo enabeled; Ground Assistance Type "Auto-detect"

  6. Set up a fail safe if you like (there are much better tutorials out there than I can include here; https://oscarliang.com/setup-gps-rescue-mode-betaflight/)

If you can see some satellites popping up sporadically it is very likely to work just fine. If you want to be sure, take your disassembled bit wired up drone outside and watch the GPS Signal Strength. (If at any point 3D Fix gets "True" you are good to go)

Step 1: Insert the Heat inserts

Into the main part where the mounting screws for the airframe will screw in.
Into both sides of the small GPS holder (marked in one of the screenshots in blue)

Step 2: Mount O4 Air Unit Pro Antenna and main part

You do not need to disconnect any of the wires.
Just make sure the antenna wires are coming out the back.
Screw in the O4 Unit using four M2x4mm Screws (do not overtighten)
The camera is mounted later.

Step 3 (optional): Mount the GPS chip

Connect the wires to the chip before installation
lay in the GPS chip and check the orientation "THIS SIDE UP"-Sticker
(Spare yourself the frustration...)

Step 4: Connect O4 Unit

Connect the Plug

Step 5: Mount the camera

Well... mount the camera in the desired angle

Tagi