Parallax Rhino - Robot Tour (2026 Science Olympiad)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A set of addon parts for Parallax's robots that improve it for use in the 2026 division C Science Olympiad Robot Tour.
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 11
- Wydruki
- 0
- Wyświetlenia
- 83
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- RC & Robotics
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
This set of parts improves a few minor annoyances I have with Parallax's small robot kits (ActivityBot and Cyber:Bot) and are designed to help the small robot kits preform better in the 2026 division C Science Olympiad event, Robot Tour.
These parts do not permanently change anything on the bot (and only require the removal of the "tail wheel"), and the Backpack can be installed with the hardware that comes with the robot kit. The Backpack is designed to work with either M3 hex nuts or CNC Kitchen's heat set inserts to attach the Plow and Caboose. The Plow and Caboose both require additional hardware to instill, all noted below. The notch in the Plow is designed to hold a 1/4 inch dowel rod.
Standard Disclaimer: At time of upload, the design has not been tested in competition and has no guarantee of performance.
Note 1: If you plan on using M3 hex nuts with the Backpack, please use the "Rhino_-_Backpack_-_M3_Rev0.stl" as it is the simplest geometry.
Note 2: If you plan to used CNC Kitchen's Brass Inserts, please use the "Rhino_-_Backpack_-_CNCK_Rev0.MF3" as it contains special geometry that can be used to reinforce the brass insert holes with more wall thickness. More details on using the "Rhino_-_Backpack_-_CNCK_Rev0.MF3" version below.
=====================================================
Printed Parts Needed:
1x Rhino_-_Backpack_-_M3_Rev0 OR Rhino_-_Backpack_-_CNCK_Rev0
1x Rhino_-_Plow_Rev0
1x Rhino_-_Caboose_-_Pololu_Caster_Rev0
=====================================================
Hardware Needed:
8x M3 Hex Nuts
1x Pololu Ball Caster OR Pololu Ball Caster
1x 1/4" wooden dowel rod (optional)
=====================================================
Using the CNC Kitchen Inserts with the backpack:
When you load the Rhino_-_Backpack_-_CNCK_Rev0.3mf into your slicer, please make sure that the slicer is treating the 3mf file as a single object with multiple parts (in Prusa Slicer click yes on the popup).
Once loaded, set the parts named "Modifier Mesh 1" as a modifier (in Prusa Slicer, select a "Modifier Mesh 1", right click on the selected "Modifier Mesh 1" and select on "Change Type", then select as Modifier in the popup). Do this for all 8 of the "Modifier Mesh" parts.
Next, set the base models settings to your liking (defaults are fine).
Select "Modifier Mesh 1" and set it to infill with 100% Concentric (in Prusa Slicer, select a "Modifier Mesh 1", right click on the selected "Modifier Mesh 1" and select "Infill", then set the infill density to 100% and infill pattern to Concentric). Do this for all 8 of the "Modifier Mesh" parts.
Then slice and print. After printing, install CNC Kitchen's M3 x 5.7 or M3 x 3 brass inserts into any through holes you are planning to use (not compatible CNC Kitchen's M3 x 5 x 4 VORON inserts).
See this Maker's Muse video for more details on the process and for a visual walk through (see 9:30 time stamp):