Liczymy pasujące modele…
Summary This is a tension member jig for 2025-2026 Science Olympiad Boomilever event. The distance between the bolt mounting hole and the bottom of the surface is 150 mm, comply with the construction parameters. It could be used for both…
This is a straight driving ETV (Egg Transport Vehicle) for the 2015 division C Science Olympiad, Scrambler. It should be fully rules complaint but check dimensions before using this design. Note: At time of upload, the design has not been…
This is a steerable ETV (Egg Transport Vehicle) for the 2015 division C Science Olympiad, Scrambler. It should be fully rules complaint but check dimensions before using this design. Note: At time of upload, the design has not been tested…
This is replacement part for the Robotgeek Gripper to allow for easier collection of pennies for the 2017 division C Science Olympiad event, Robot Arm. It should be fully rules complaint but check dimensions before using this design. The…
The Hub Bub Odd is a very simple Wind Power wind turbine for the 2017 division C Science Olympiad, based on the original Hub Bub . It should be fully rules complaint but check dimensions before using this design. The Hub Bub Odd is an…
This a Egg Backstop (aka the egg block) for the 2015 division C Science Olympiad, Scrambler. It should be fully rules complaint but check dimensions before using this design. Best way to attach it is glue. Note: At time of upload, the…
This is a very simple Wind Power wind turbine for the 2016 division C Science Olympiad. It should be fully rules complaint but check dimensions before using this design. The Hub Bub is an easy to attach hub that allows 1/8" wooden dowels…
The WRO RoboSports discipline needs ramps on the mat. This model provides 3D printed parts for a simple assembly, especially regarding a sharp edge at the front of the ramp. For assembly 3mm foam plates are required. Drawings are included…
The RoadRunner is a simple to build modification of the Tomahawk Electric Vehicle. Both the RoadRunner and Tomahawk were Electric Vehicles built for the 2016 division C Science Olympiad. The purpose of the RoadRunner is to create a much…
Simple base for Science Olympiad event Machines. Hollowed out to remain structural strength while allowing for less filament and faster print time. Holes are designed to fit a 10mm linear rod from McMasterCarr. Printed on an ELEGOO…
Parts to launch the ETV (Egg Transport Vehicle) for the 2015 division C Science Olympiad, Scrambler. It should be fully rules complaint but check dimensions before using this design. 2015/2016 redesign: To make it easier to launch the…
This is a simple wing rib for the 2014 Science Olympiad event, Wright Stuff. The length of the rib is 66 mm and it is 1.5 mm thick. Category: Engineering
This is a proof of concept for a geared braking system on the 'gravity vehicle' for 2013 division C Science Olympiad Competition. This is / can be made fully rules compliant, with the 2013 rules, with very little modification. Note: This…
This is a very simple, in line, Robot Arm extenders that fit onto the RobotGeek's V.2 Robotic Arm for the 2017 division C Science Olympiad. It should be fully rules complaint but check dimensions before using this design. The BeefyArm…
This is a test stand mount that allows 1-1/4 inch PVC pipe to be mounted to a board and banana jacks to be inserted.
Designed to be used with the following mirrors, found on Amazon: Mirrors I found that printing the intended mirror surface face-down on the print bed helps for a nice flat surface.
This is a very simple It's About Time metronome / pendulum clock for the 2016 division C Science Olympiad. It should be fully rules complaint but check dimensions before using this design. The Clunky Clock is designed to use parts I have…
This is a bolt on set of extensions that fit onto the OWI-535 Robotic Arm Edge for the 2017 division C Science Olympiad. It should be fully rules complaint but check dimensions before using this design. The Gamma Mods are designed to…
This is a straight driving Electric Vehicle for the 2016 division C Science Olympiad. It should be fully rules complaint but check dimensions before using this design. Note: At time of upload, the design has not been tested in competition…
Summary This device can help you make equilateral triangular legs for the Division C Tower Event in the Science Olympiad. This helps people who don't want to sand the legs manually using sandpaper but don't have an electric sander. You…
This is a slide on set of gripper/extensions that fit onto the OWI-535 Robotic Arm Edge to allow for easier collection of pennies for the 2017 division C Science Olympiad. It should be fully rules complaint but check dimensions before…
This is a very simple, in line, Robot Arm extenders that fit onto the RobotGeek's V.2 Robotic Arm for the 2016 division C Science Olympiad. It should be fully rules complaint but check dimensions before using this design. The Armlong will…
A center marker for the air trajectory build event at Science Olympiad.
It's a box. Customizable with whatever text. You can glue on handles. It also has a lid. Lid has a rectangle meant for tape so you can label it. Designed for the WiFi Lab event in Science Olympiad To customize the box body, import the STL…
Fits the rules associated with the box for SciOly Flight 2024
This is a very basic air duct for use in the Hovercraft event for the 2017 division B/C Science Olympiad. It should be fully rules complaint but check dimensions before using this design. The Aero Kinetic Redirector or AKR for short (my…
Model was made by the Air Trajectory coach (i.e. not by me). However, it is an original model, not downloaded from the internet.
Summary This set of models is for the Science Olympiad Material Science C 2025. The lab portion of the event requires teams to make concrete pucks of certain dimensions. The dimensions of these models comply with 2025 rules, the diameter…
This is a very basic bolt on set of extensions that fit onto the OWI-535 Robotic Arm Edge for the 2013 division C Science Olympiad. It should be fully rules complaint but check dimensions before using this design. The Alpha Mods are…
Olympic Cup for Dolls. You can also print in a larger size.
This jig helps you position the tension rods of a div c boomilever at 15cm, use as the photos show. Not built for div c bonus but. Is suitable for div b bonus. (For tension boomilevers)
This is my first attempt of making a jig for my middle school students to use during the Optics event of Science Olympiad. In that event, they are to place mirrors and predict where a laser beam will go. They have only a few minutes to…
This set of parts improves a few minor annoyances I have with Parallax's small robot kits (ActivityBot and Cyber:Bot) and are designed to help the small robot kits preform better in the 2026 division C Science Olympiad event, Robot Tour.…
a model designed to fit over CDs to give more traction when making science Olympiad projects or just projects.
Science Olympiad 2026-2027 Boomilever Division C Bonus and Non Bonus Jig This is the Division C Boomilever building jig. The backplate includes 2 mounting holes which could be used for both Bonus design and Non Bonus Design with only one…
Science Olympiad 2026-2027 Boomilever Division B Bonus and Non Bonus Jig This is the Division B Boomilever building jig. The backplate includes 2 mounting holes which could be used for both Bonus design and Non Bonus Design with only one…
The jig design aims to minimize the amount of filament used by your printer when printing a large (otherwise full of infill) jig. The use of this specific jig will not be very useful in years following, but the design can be modified.…
This is a counter weight jig for 2025-2026 Science Olympiad Machines event, useful for actively adjusting the position of a counter weight for a machine. This object does need supports. Height is 9.4 cm, width is 2.5 cm, length is 5.5 cm
This set of parts improves a few minor annoyances I have with Parallax's small robot kits (ActivityBot and Cyber:Bot) and are designed to help the small robot kits preform better in the 2026 division C Science Olympiad event, Robot Tour.…
This is a counter weight jig for 2025-2026 Science Olympiad Machines event, useful for actively adjusting the position of a counter weight for a machine. This object does need supports. Height is 9.4 cm, width is 2.5 cm, length is 5.5 cm
a model designed to fit over CDs to give more traction when making science Olympiad projects or just projects.
A center marker for the air trajectory build event at Science Olympiad.
This model was specially crafted for wheeld vehicle competition, with this 3d printed part you can easily upgrade your wheeled vehicle quickly and cheeply.
![[RobotGeek V.2] BeefyArm - Robot Arm Mod (2017 Science Olympiad)](https://media.printables.com/media/prints/219412/images/1998845_8d9dcac3-700a-4640-94c3-ad54b9e58640/d98898f287af5f5cf4b9cd00b4ad35d4_display_large_21.jpg)
![[RobotGeek V.2] ArmLong- Robot Arm Mod (2016 Science Olympiad)](https://media.printables.com/media/prints/219409/images/1998817_7b06f363-0ac3-4a22-8d61-53b833f0590c/06f143485f34d95685ca062f6f0eecf9_display_large_21.jpg)
