1 / 3
Rancilio Silvia Group Head Shroud Halo Light Upgrade — zdjęcie 1
1 / 3

Rancilio Silvia Group Head Shroud Halo Light Upgrade

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Upgrade for the group head shroud that also illuminates underneath.

Ocena
0 / 5
Polubienia
1
Pobrania
10
Wydruki
1
Wyświetlenia
282
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Kitchen
Licencja
Creative Commons — Public Domain

NB:This is for a first generation machine. It may work for later generations. Have not tried but would be interested to know if it does work with newer machines.

The shrouds on these machines are quite thin and tend to break after a few years. i wanted to replace it but figured I should upgrade it to accomodate silicone foam insulation left over from insulating the boiler and illumination for early mornings.

Halo lights for automotive projector headlights are common and come in many sizes. Even the cheap Aliexpress ones are consistent. All that's needed is a power supply, a hall effect dimmer switch is highly recommended as the reflection off of the stainless steel is blinding.

purchased parts:

- 12v Halo Ring Light (100mm) -

https://www.aliexpress.com/item/1005006170863377.html?spm=a2g0o.order_list.order_list_main.5.2e881802dkmhiD

- 12v 12w 1 power supply (B-12W-12V-1.0A) -

https://www.aliexpress.com/item/1005007377920277.html?spm=a2g0o.detail.0.0.3b5eKyTHKyTHtL&productId=1005007377920277&pdp_ext_f=%7B%22tabScene%22%3A%22retail%22%2C%22sku_id%22%3A12000040491403171%2C%22origProductId%22%3A%221005007377920277%22%7D&

- Dimmer Switch

https://www.aliexpress.com/item/1005007110424498.html?spm=a2g0o.order_list.order_list_main.20.2e8818026HeK3T

Consumables:

- solder or crimps (I used dupont connectors for the halo light so it's easier to assemble/dissassemble but solder is fine)

- 5mm heat shrink (I used uncoated to hold the dupont connectors together and 4/1 glue lined for my unsealed terminals)

- fork terminals (I think these were 4mm, I 'm not sure. I prefer tu use unsealed terminals with glue lined heat shrink but pre insulated is fine)

- electrical tape or kapton tape (to provide a barrier between the ring light wires and the back plate of the machine.

- super glue and glue gun (do not use the glue gun for sticking the ring light to the shroud, the heat will cause it to fall out. use super glue for sticking it down and a big dab of melt glue from the glue gun for covering the wires at the solder point on the ring light)

- cable (to match the halo lights to the dimmer switch and from the dimmer to the power supply was about 0.5mm/24AWG, the power supply to the main switch I just used the wires out of an extension lead)

- 6.3mm piggyback spade terminals (to patch in to the outlet of the on switch)

When printing the parts, I recommend ASA or ABS. PLA will warp. For the group head cover shroud, I also recommend printing with the cavity for the insulation pointing down and the shallower cavity for the ring light pointing up with supports. the supports inside the deeper inulation cavity are a bit easier to remove cleanly and the ring light mating surface will be ironed flat as the top surface for better adhesion. The supply and dimmer mount should be pretty obvious.

I mounted the dimmer and power supply under the water tank for space and simplicity. There's a water deflector shield above it and the mount will keep it elevated off of the chassis. There are pre existing holes in tyhe base I used to screw in the mount. If I remeber correctly the mount was skewed but I neglected to update the model (sorry) and left it as is.

The grouphead cover shroud has a open cavity on the inside for a strip of 3mm silicone foam to insulate against the group head. the ring light should be glued down with super glue into the shallow cavity (DONT use melt glue to stick it down). Melt glue should be used to coat the wires at the solder point of the ring light.

it should be wired as such:

Ring light - dimmer switch - power supply - on switch. The power switch is 2 pole so power and ground for the supply can both come from it.

Lastly, The light is very bright. I turned the dimmer switch all the way down so as not to blind myself in the early mornings.

I think thats everything. I hope this helps.

Tagi