137 modeli
Original design was in Fusion360 with no printable files. This is a simple remix with no changes to original design. Note that the two brackets are best printed on the side to get maximum hanging strength. Brackets are also printed with…
This is a nozzle for the Rancilio Silvia water outlet. If the drip tray is not pushed all the way back, water can run onto the base plate and the Silvia will begin to rust. With this nozzle do you fix the problem. The inner diameter is…
Remixed from this design . The original design is missing a very small feature compared to the original Rancilio part - a shallow cut in the top front part that accommodates the front panel's bottom lip. That's the only difference.
Since the height under the brew group is limited, I designed a space-saving adapter to hold the loadcell. It is easily printable without support, ideally made of some temperature resistant material. As the Silvias have slightly changed…
An angled base with a removable platter and a couple dosing cups to make the old Rocky look and work a bit like a Niche Zero. This base replaces the stock baseplate on the Rocky and re-uses the stock hardware. Both power switches are…
Update of memyself s nice rancilio-silvia-loadcell-mount model: The mount is slide-on so it doesnt move on the machine (no glue needed) I modified the holes for flat/countersunk screws The tray holders are slightly thicker and can now be…
This easy to print funnel distributes the coffee at max level of an 58mm basket. For my Rancilio basket it seems to be optimal, but for other filter baskets my not be good. Advised to print in PETG, but if you do not preheat the…
Stronger version of the original. Slightly bigger.
Nextion 2.4 inch display enclosure that fits the front panel of Rancilio Silvia V6. Intended to be used as part of a Gaggiuino install. The design leverages the V6 power and boiler indicator lights to route the wires to the screen. It…
This Umikot compatible tamping station for Rancilio Silvia Portafilters (botomless or stock tested) can fit Umikot with bases ears/lug width set for LM (28,5mm) (see workspace on original work). I keep the design minimal so that it can be…
This is a spout for the Rancilio Rocky coffee grinder. My spout cracked on my rocky some years ago. I made this and love how it pours coffee down into my aeropress or into a jar I use for the day's espresso grinds. Picture is printed in…
I needed something to store the parts of daily usage for our coffee maker. The basic model is created in freecad, the pattern in the bottom is done in tinkercad. I printed it with some supports for the upper holders. Its done in nice…
Drip tray support shelf that makes it easier to remove the drip tray to empty it. By elevation it, splashes from the spout will not make it far back onto the body of the machine that is prone to corroding. The spacer for the front reduces…
I have created a modular Steam Knob for my Rancilio Silvia v3. (not sure if the part fits to previous or later models) I have printed the insert piece in PETG, the Knob was printed in Wood PLA+ I used a lighter to melt the top of the petg…
This model is a remix of Loogle's Gaggia Classic / Pro touchscreen enclosure. That model is a remix of a project from LikeableBump. Consider visiting these projects and liking them!…
After trying to implement some mods that I found on Reddit and forums, and not being satisfied, I decided to develop my version using gears. Printed with 0.2 mm height, in PLA, 5 walls, 100% infill (I think you can reduce the infill, but…
This is a extension for the 3way valve. It helps the water getting into the tray.
A doserless conversion for the Rancilio Rocky. This remix uses an open chute so you can clear out the retained grinds. The Rocky retains ~1g of coffee and this lets you clean it out easily. You'll also need to print the retention clip…
A doserless conversion for the Rancilio Rocky. This remix uses an open chute so you can clear out the retained grinds. The Rocky retains ~1g of coffee and this lets you clean it out easily. You'll also need to print the retention clip…
In a video on espresso dosing by my new favorite YouTuber James Hoffman , he showed how a portafilter funnel can help with the distribution of grounds. I did a quick search on Thingiverse to find such an item to print, but the search Gods…
This is part of my Rancilio Silvia Gaggiuino build, I use this splash guard to prevent the scale housing fall into drip tray, also prevent splash from solenoid.
Water sensor XKC-Y25-NPN holder for Rancilio Silvia espresso machine. You can use this with the CleverCoffee ESP32 modification for espresson machines. Also gaggiuino might support the sensor in the future - if its built into a Rancilio…
I love my Rancilio Rocky coffee grinder. I don't, however, love the open bolt access holes in the bean hopper that invariably collect a few beans each. When you only put in as many beans as you want, this is a problem! This plug has a…
I was looking for a possibility to store my group handles near the machine. I don't had a lot of space left and right, so I decided to mount it on the side of the machine itself. I would be happy to get some feedback for improvements. You…
The hole for the steam knob stem was pretty large and would allow for the wiggle of the knob. I designed this insert to reduce the hole size from 25mm to 20mm to help reduce the unwanted bending on the knob while turning. It was printed…
Requires 10-32 screws, 2.5" lg, qty 3
As result of a community request I redesign my Tamper Station Rocket E61 to RANCILIO Espresso machine. Changes are: Height of the stay not so deep. => to 28,1 mm (instead of 37.2 mm) Lateral intake change a little bit for better fit. =>…
This is a magnetic funnel for my Rancilio Silvia Espresso machine. I've been using it successfully for the last 6 months and vouch that it works as needed. It uses tiny 3 mm diameter x 2 mm high magnets, 12 of them so that the grip is…
I introduce a bellows system for the Rancilio Rocky Doserless grinder. I've been drinking a lot of filter coffee recently. Instead of adjusting my other grinder between espresso and filter settings, I pulled the Rocky Doserless out of the…
This is a holder for a Portafilter fitting a Rancilio Silva
Just a simple water tank lid for rancilio silvia. Modeled after the original. Also included the split version for smaller print beds. Print Settings Printer Brand: UltiMaker Printer: Ultimaker 3 Rafts: Doesn't Matter Supports: Yes…
Fits Standard Rancilio Silvia (with or without PID) Fits the original stainless steel grid One-hand handling for easy morning workflow Free Pantechnicon Design sells a pricey 3D-printed drip tray mode for the Rancilio Silvia Pro/Pro X…
I designed this for the Rancilio PID hack. I didn't want to put a hole into the machine, so I went for a magnetic holder. It sits reasonably tight, has a little slot to guide the cables and fits the standard OLED SSD1306. Sometimes you…
Mod to have the Precisa scale flush and not loose much height for your cofee mug. Also prevents the mug and the scale from a hike if the pump is running Highly recommenden for Leva ITO Mod Print in ABS so it survives the dishwasher. For…
Remix of the original model, but for load cells with a 10mm screw distance (instead of 15mm). I found my load cells had different screw distance as well as differently sized screws, which varied from the official Gagguino…
Heads-up: I kept tolerances quite low, so no guarantees that this will fit your machine. Pause at the beginning of layer 12 to insert magnets, or use the ‘no_magnets’ version with double sided tape. I inserted 20 magnets, which is a bit…
I made it vertically with rPET. I use support but probably you could print without. Layer height 0.2mm, infill 20%(maybe good idea to make large wall thickness). It has a little crack(see photo) that I fill with super glue. 6 month past…
Prevent water from seeping beneath the drip tray of your Rancilio Silvia with the addition of a solenoid spout extension. It guides water directly into the drip tray, eliminating any potential mess. Easy to install - simply push it gently…
I was asked to create a housing for the Silvia V3 for the Nextion 2.4" screen. This version should fit the original switch and use it to hold the housing to the machine. Its made to fit a 8mm panel indicator neon (…
A Cupmat for the Rancilio Silvia.
Designed this housing to mount to the bottom of my Rancilio Silvia V3 coffee machine to fit the following components: A Clever Coffee PCB And a Meanwell RS-15-5 power supply The housing has a snap fit lid and is bottom mounted to be as…
An adaptor for the stock 2.1" screen case that hooks onto the top lip and moves the screen down to cover the power switch for a cleaner look and easier access to the cup warming lid.
A mat designed to sit on top of the Rancilio Silvia espresso machine. Keeps the stainless steel on top from getting scratched by your cups or anything else you keep on top of your machine. Also has a raised edge to prevent water from…
Remix: Slightly shorter spout as not to interfere with the driptray.
A modified version of the Rancilio Tamping station to fit the 20-112-030 portafilter used with the Rancilio Nancy, Audrey, and Kathy machines. Category: Kitchen & Dining
I designed this part to tidy up my build a little. The PCB sits on the right leaving just enough space to mount the SSR next to it. If you can you should connect the JST headers before installing the SSR because everything is a little…
I printed mine in PLA, 0.2 mm height, 20% infill, 3 walls (4 or 5 would be better). I also made improvements to make it stepless, minor improvements or adaptions to the funnel and anti-popcorn lid. Consider also printing: Stepless…
I suggest using PETG or another somewhat temperature resistant filament. It will see a little hot water and steam. There are some "high temp" PLA filaments around that might also be ok (I've not tried). If you're a careful coffee maker,…
This is a cover that friction fits over the original round, black steam knob. As it is just a cover for the existing knob, it avoids all the issues around reverse-engineering the existing shaft and metal clip. This does mean however that…
This model is a completely printed drip tray and drip grid for the Rancilio Silvia v5. The model is designed so that a Loadcell can be installed between the support plate and the drip tray. The necessary brew-by-weight conversion has been…
Update 25/11/2023: Updated Model to have an interior lip to prevent coffee build up along the rim of my portafilter. Added G-Code and 3MF file to MK4IS. Magnetic Dosing Funnel for the Rancilio Silvia. 12 holes for 3mm x 3mm round magnets.…
My 04' Rancilio Silvia's ULKA pump was getting pretty noisy. I opened it up and the vibration dampening holders of the pump were pretty saggy. I replaced them with these and the noisy reduction was quite obvious. Important: print it in a…
I found a similar model on thingiverse in the past, but there was a defect on the design and all my attempts to print failed. Then, I redesigned from scratch and now it is printing perfectly. I used a TPU from Overture, 95A:…
This spout for the Rancilio Rocky has an integrated hinge so the top can be lifted to clean out any coffee buildup in the spout, rubber gasket, or internal chute. This also allows for some inspection of the internals of the grinder. This…
The Rancilio Rocky is a popular coffee grinder with one major annoyance: beans and ground coffee get caught in the deep screw wells of the hopper. Beans are easily tapped back into the burrs, but the grounds remain and eventually turn…
This printable can be used with the Rancilio Rocky coffee grinder, it prevents coffee beans from getting into screw holes that keep bean container attached to the base. Servicing this grinder requires unscrewing the dome cover inside the…
Replacement for Rancilio Rocky e clip. If you have lost yours and need a replacement then maybe this can help (Lost the original, I am sure the fairies took it). Due to small feature size, I used a 0.2mm nozzle to print this. Line width =…
This Version 2 of the Espresso Puck Prep Station (Version 1 https://www.printables.com/model/1156302-rancilio-silvia-bottomless-portafilter-espresso-pu ) both levels and elevates any Rancilio Silvia Portafilters (default factory one, and…
Needs supports for the ears - set the support generation to something low like 10 degrees so only the overhangs get supports. Enjoy!
Needs supports for the corners
This is a housing for a XMT7100 PID temperature control. You can use it to control the water temperature in the Rancilio Silvia espresso machine. The housing holds nicely onto the top crease of the Rancilio Silvia espresso machine. It is…
Printed in PETG quite tight tolerances for me. It's just made in prusaslicer and saved as a .3mf file so you can tweak it however you like.
An adapter for the @0x64_2343909 's 2.8" Lilygo case for Rancilio Silvia and Gaggia classic. I designed it because didn't find any alternatives. Optional space to glue 10x2mm magnets. My Rancilio Silvia is wrapped so let me know if you…
This is a trivial model to reduce the diameter of the hole that a steam knob goes through. I printed it in TPU and it fits very easily. I made the lip that goes on the other side of the front so small that I suspect a stiffer material…
The portion of the design that attaches to the machine is the same as the original from @legojoey17, but I created a new base for the drip tray to it on. The tapered design was chipping at the edges because it was so thin, so I created a…
Espresso Puck Prep Station to both level and elevate a Rancilio Silvia Bottomless Portafilter https://amzn.to/4hn7AzP . Modular 2-part print (separate leveler and riser) Leveler levels and stabilizes the naked portafilter so it's…
This model uses SKÅDIS T-nuts mounting system, I am personally using M2.5 screws, if you'd be interested in M2 option, just let me know and I'd create additional model. Extra parts needed Qty Description Sourcing 2 M2.5 DIN934 Hex Nut…
Remix of FunnyGermanGuy's remix of Laurman's Rancilio Silvia Screen Mount over on Thingiverse. I added a bottom plate with an integrated magnet which is screwed on the top part because I didn't want to glue it on. Top part is mostly…
So, as most of the nerds here are happy to enjoy a great espresso, I hacked down an adapter for connecting the water filter from BRITA directly to my Rancilio Silvia. Combined with a water level hose, you'll never have to buy these…
Rubber grommer to install in the hole for the steam know hole. Reduce wooble when tuning the knob. printed using TPU
This tray fits tightly around the metal base of the older style Rancilio Rocky coffee grinder, and catches any coffee grounds that fall. Easy to take off and clean out, with rounded edges all around the bottom area.
Hi here is my very easy and simple conversion of oldstyle italian espresso grinder machine into doserless fresh grinder that is possible to use for alternative methods (aeropress, V60, Batch Brew,…) or you can still use it as a espresso…
Initial Design by SaddamCZ
Print the shute with support (I prefer the snug since it's easier to remove). I used a TPU from Overture, 95A, for the seal: https://geni.us/4Qa3O (obs: affiliate link, but you don't pay more if you buy from this link). Consider also…
The front wall of the liner is lower than the other sides to allow insertion and removal of the drip tray; make sure you insert the liner with the lower wall facing outward. The liner is a snug fit in the drip tray slot; gentle downward…
Extension ring to fit to the original Rancilio Rocky lid. Just manually move it up and down a few times to push/blow the last grinded beans out of the grinder to clean it out and leave no beans behind.
Bevorzugt PETG oder widerstandsfähigeres Material. Druck mit Stützen an den “Haken”. Standardprofil 0,2mm in Bambu Studio.
Scale load cell mount and tray holder for 750g cell which has 7.5mm screw hole spacing.
Kdykoliv jsme vařili kafe a potřebovali odstříknout páru nebo horkou vodu, tak tak navzlínala nebo natekla štěrbinami kolem nerezové mřížky do přístroje. Kávovar má sice v prostoru pod miskou otvor pro odkapání, ale vyteče to na linku pod…
I made this model to attach to the front of my Silvia. Take out the Rancilio sign on the front, and this should screw into the place of the two holes. You will need to make a small hold under though to route the cables.
The original Rancilio Rocky grinder hopper came with a fixed end stop screw which meant that some grinders were not able to grind as fine as they otherwise could for espresso. Replacement hoppers sold now come with an adjustable end stop…
The original version was a fraction to tight on both Lelit's and Rancilio's portafilter's so I increased the inner diam. Not tested yet. new version added today 23.05.2023. I had previously exported the file in meters and not in mm. Now…
I bought and overhauled a quarter century old Rancilio Silvia. During cleaning, the already faded printed brand logo completely disappeared. Newer versions of the Silvia have a physical emblem, so I designed my own. I had to gauge the…
Late night, trying to load coffee grounds into the filter in order to jump-start my brain with a jetfuel espresso, making a big mess because our Elektra portafilter is too big for the support forks on our Rancilio Rocky grinder. Isn't it…
Inspired by https://www.thingiverse.com/thing:4378235 , I wanted something that is closer to the unit and worked with my 51mm portafilter. Print Settings Printer: BIQU B1 Rafts: No Supports: Yes Resolution: 0.2mm Infill: 50% Filament:…
Remixed Racilio Rocky 15° Tilt Base. Removed doser cups and clean up foot for support. I have a older Rocky and thus had to cut off the nub on the back but it sits well with just the two front screws.
My Rocky doesn't have a bean disperser, so beans get caught in the screw holes. I used to cover them with tape, but finally genned this up in Tinkercad. Print Settings Printer Brand: MakerGear Printer: MakerGear M2 Rafts: No Supports: No…
A grip tab for the 8mm diameter steam wand used on many Rancilio machines. You should apply a drop of oil to the wand before trying to install this as the fit is intentionally very tight. Intended to be printed in TPU Category: Kitchen &…
This spout helps the Silvia 3-way valve water discharge into the stainless-steel drip tray and not into the base of the Silvia where it will promote corrosion long term. To further mitigate corrosion, I've put some 2mm thick EVA foam…
Mirror: https://www.amazon.com/gp/product/B000RZQI68/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 6mmx3mm Magnets: https://www.amazon.com/gp/product/B07873ZCY4/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 Recommended Print Settings…
This is a mount for the Nextion 2.8 screen on a Rancilio Silvia. It is designed to slot into a cutout in place of the front logo. The plate is designed to slot into a 76.30mm wide and 55.30mm high cutout. I recommend using hot glue to fix…
Fits Rancilio Silvia and maybe other 58mm models as well Prints with supports
Mount for two Wago 221-413 that can be installed on the original cable relief of a Rancilio Silvia espresso machine. Printed in PLA, 0.2mm, 15% Infill and no support. Print it on the side with the two hex holes
Rancilio Rocky doserless Conversion with adapter and swappable spouts/chute. It uses the same retaining clip as the original conversion model but i redesigned the rest. Adapter was printed face down with support for notches and spout…
Made it for my Rancilio Silvia Pro X but it should fit any 58mm portafilters
Even with the silicone mod protection at the seam, if the drip tray is not pushed all the way back, water can run behind the base plate and cause the Silvia to rust. This nozzle guides the water into the tray, even if the tray is…
If you want to go this route, prepare angle grinder :) So far there are 2 main components: - Funnel which I use with printed TPU bellows. This is press fit and should be fine for the angle of legs - Legs and spacer to support the grinder…
Eliminates one more place that beans get stuck in the Rancilio Rocky grinder chamber. I also like to use these little nubs to prevent beans from getting stuck in the screw holes for the diverter. Food Safety Printing a part from food safe…
I used Scotch Bumpers for grip. You can use any feet that's <13mm. STL file without feet holes is slightly taller. Features: Concaved the inside to make it easier to clean. Size and corner radius matches the hopper cover. 13mm holes for…
Holder for a Rancilio Bottomless Portafilter, allowing the portafilter to remain level on your work surface
