Remix - Filament Spool Drybox – Ikea 365+ – Fitted for V3 KE - with Indonesian Parts Links
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Mixed and matched many models to create the perfect drybox for me, where the parts can be bought in Indonesia.
- Ocena
- 0 / 5
- Polubienia
- 2
- Pobrania
- 16
- Wydruki
- 0
- Wyświetlenia
- 240
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Accessories
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
After looking through many dryboxes, I finally decided to mix and match models to create the perfect drybox for me! I chose models for the drybox where the parts can be found and bought on Indonesian online shop (Shopee). For the print files, please find them on the original model.
First of all, here's the parts that you need to buy beforehand - and for my Indonesian friends, I've attached shopee links - with no additional expense to you) if you want to buy the parts. Parts listed are for 1 box.
1. Ikea 365+ Box - https://s.shopee.co.id/3qHFfBiiWW
2. 608 Bearings (8 pcs) - https://s.shopee.co.id/7VAY263yMq
3. Pneumatic Connector (PC4-M10) (2 pcs) - https://s.shopee.co.id/50TD3YCccL
4. Round Hygrometer - https://s.shopee.co.id/4VWwSXYPVZ
5. PTFE Tube - https://s.shopee.co.id/3VePGpYmOa
Now, here's the list of models I used:
Filament Drybox
(Obviously) I used Pyry's drybox as the base. I've printed other drybox system for Ikea 365+ but it seems the filament won't roll smoothly. This is the best base and it fits the box EXACTLY as it is. Also, as my printer can't print the entire base, I've cut the model a little bit to fit smaller printer.
Link: https://www.printables.com/model/866936-filament-spool-drybox-ikea-365Silica Gel / Desiccant Container
I used Pyry's remixed desiccant container so that my silica gel beads won't come spilling everywhere.
Link: https://www.printables.com/model/1355244-silica-container-with-smaller-gap-for-pyrys-filamePTFE Filament Pass Thru
I found this model where the pneumatic connector is flush with the box, and I like how the hygrometer is placed.
Note: You need to print the holes higher than shown in the model. If it's too low, it will cause friction and make it hard for the printer to pull the filaments. I've attached a drill guide PDF. Just print the PDF, cut according to the lines, line it up in the middle of the box, and use the dot as a guide to drill!
Link: https://www.printables.com/model/1014211-ptfe-filament-pass-thru-through-for-dryboxPTFE Tube Cap
I don't like the PTFE tube snaking all the way from the box to the printer, so I decided to cut it short and printed a TPU cap instead to seal when not in use.
Link: https://www.printables.com/model/28918-ptfe-tube-cap-4-mm
Filament Spool Silica Gel / Desiccant Container
I wanted to add more silica gel in the box, so I decided to add more inside the spool. I ended up choosing this model as I feel this one allows more air to pass through the beads, and the end plug causes the container to fit inside the Ikea box nicely.
Used Files:
1. container_50x75_fullcore_v2
2. lid_50_v2
3. center_plug_v2


Link: https://www.printables.com/model/1367-malolos-silica-gel-desiccant-containers/files
Note:
The painters tape on the right side of the rollers is because my TPU filament spool is made of plastic, so it does not grip the rollers that well, hence the tape. However in the picture, it's currently swapped with my PLA spool, so it might be confusing.