1 / 14
Core ONE / + bed stop rear with anti-vibration bearing — zdjęcie 1
1 / 14

Core ONE / + bed stop rear with anti-vibration bearing

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

anti-vibration bracket for the rear ,,Z axis with MF 128 2Z bearing. My model reduced vibrations ,,Y 93%

Ocena
5 / 5
Polubienia
175
Pobrania
335
Wydruki
19
Wyświetlenia
2792
Oceny
19

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
GNU General Public License v2.0

UPDATE 19_10_2026

This model is intended for CORE ONE/+ printers; I have not tested it for Gen2, and it is incompatible with the INDX. I will release new versions as I upgrade my own printer.

The new CORE ONE L printer uses anti-vibration mounts on the Z-axis trapezoidal screws.

I modified the model to fit on the CORE ONE / + printer.

My Core One + after phase stepping calibration, reduced the vibration of the "Y" motor by 93%

(ZEN)    MF 128 - 2Z  /bearings

8×12*3,5×0,8

I purchased the bearing here in the Czech Republic.

ZEN MF 128-2Z kuličkové ložisko s přírubou | Prumex.cz

( 24.1.2026 _ I asked Prusa Support if this bearing could appear as a spare part, for the CORE ONE L and XL printers, where it is used. I was told that it is for a long time? and sent an external link.? maybe it will help someone with the bearing. :-)

Let's be surprised, maybe it will appear in the e-shop someday :-)

https://www.123bearing.com/bearing-housing/deep-groove-bearing/single-row/mf128-2z

D - 12mm

d - 8mm

D1- 13,2mm

B - 3,5mm

C - 0,8mm

Print

I recommend PCCF material !

print settings in 3mf file

5 -  perimeters

Solid layers top - 7, bottom - 7

Infill - 20%

I recommend this support setting. My print failed with organic supports.

Style - Grid, Top contact Z distance: 0,1mm, Pattern spacing:5, Interface pattern spacing:0mm 

Support enforcers only

Pay attention to the screw holes, there must be no supports here !!!!

tested on multiple prints, PCCF supports are easily separated from the model. Please note that with this setting, small visible marks will remain on the bottom of the model. They are on the bottom and cannot be seen after installation.

The supports can be easily removed, you can use a knife to help you.

Construction

Unscrew the two screws and keep them for reassembly.

all installation material will be reused

remove the back cover

remove the rear screw of the bed stop rear part

remove the 3 screws of the bed stop rear part

Remove the original square nuts and insert into the new model

Check the holes before inserting the nuts, and clean them with a file if necessary.

check the alignment of the nuts

Test the screws before assembly, they must move freely.

Insert the bearing, the part has a small tolerance to fit tightly, it requires a little force.

When installing the bearing, do not press on the springs, hold the model by the bearing housing!!!

Set the print bed down in the menu control

Install the new bed stop rear part, this requires patience and perpendicularity when installing.

Rotate the part into the correct position, this will require a slight deflection of the threaded rod, proceed carefully.

screw in two screws

screw in the rear screw

screw in the third screw, this screw will create its own thread during installation, tighten gently

perform a z-axis alignment calibration

I recommend buying an accelerometer and doing a phase stepping calibration. In my case, the vibrations of the "Y" axis were reduced by 93%

Tagi