Geeetech A20M stabilizers for Belted Z (KevinAKASam)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Geeetech A20M stabilizers for Belted Z (KevinAKASam)
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 8
- Wydruki
- 0
- Wyświetlenia
- 71
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Printer Parts & Upgrades
- Licencja
- GNU General Public License v3.0
This is a set of stabilizers for the Geeetech A20M for use during/after conversion to KevinAKASam's Belted Z mod. It is intended that for one of the stabilizers you use the 355MM leadscrew as part of the stabilizer, while the other stabilizer will be mostly 3D printed. If you do not want to use the leadscrew in one of the stabilizers, you can just copy print an additional set of braces+adjuster from the Right side stabilizer package. This does reduce the max Z height to about 230.
Printing
I printed this almost entirely out of ABS (5W, 5T, 5B, 25% Adaptive Cubic infill) though you could likely get away with PETG in a pinch. The .3mf files have the parts oriented and the integrated supports positioned, so you should just have to change your printer type and filament. If you don't want to use the integrated supports, you can delete them and use slicer generated ones, but I had much better results with the integrated ones. All models are included in the step file.
Assembly
The left stabilizer can be built and installed with no drilling required, as it uses the wire pass-throughs to mount to the base plate. You will need to disconnect the cables that exit the two large pass-through holes (one top, one at the rear) and remove the rubber grommets that are installed. You may need to temporarily remove the IEC socket and power input leads from the internal power supply while installing in order to get clearance to tighten the nut. Install the upper brackets the same way you do on the normal belted z mod, using two longer M5x20mm screws on the backside and the standard M5x8 on the front. Install the Top Lock block by screwing it on to the leadscrew until the end of the leadscrew is flush with the top. Then thread on the Top locking flange, followed by the Lower lockdown plate and finally screw on the Lower lock nut. Use M5 screws and nuts to secure the Top locking flange to the top bracket, the adjust the lower lock nut until the 2040 riser is perpendicular to the base using a machinist's square. Install 4 M5 nuts in the base, then use 4 M5 bolts in the Lower Lockdown plate to lock the position of the entire assembly. Recheck and adjust as necessary if you lose perpendicularity during tightening. You can now re-run the wires through the bottom bracket up to the Z and X motors and related endstops and then the heater+thermistor and Y endstop wires through the rear passthrough.
The right stabilizer will require drilling 4 holes in the upper deck. There is a drill guide included in the step files that you can use to help align these holes. Additionally, the right stabilizer will require 6 M5 heatset inserts. Use button head M5 screws on the underside when mounting as you will need a ball-head allen key due to the slight angles cause by the protruding sheet metal and the smaller allen key used on the button head will go right through the hole that is made when you unscrew the bottom rubber foot, allowing you to tighten the outside corner screw. When installing the right stabilizer, start out with the upper and lower attached to the adjuster and bring them in to the shortest length. Make sure that the locking points are aligned, if they are not, remove one side and turn it a quarter turn before reinstalling on to the adjuster - repeat until the locking points are aligned. Attach the assembly to the bottom mounting bracket, then use the adjuster to lengthen the stabilizer until it seats in the upper bracket. Once seated, install the upper mounting screws to affix the stabilizer to the top bracket. Then, use the adjuster to lengthen/shorten the stabilizer while using a machinist's square to ensure the 2040 riser is perpendicular relative to the base. Once satisfied, lock the adjuster in place using the two M5 screws in the upper and lower stabilizers.