2.5" SSD or hard drive cage with spots for side mounted 80MM fans. Holds up to 3 drives that are 7mm 9.5mm or 15mm. Support for SATA, SAS, U.2
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
This is something I designed from scratch to use in a Sliger CX2177a case I used to build a server. This will allow…
- Ocena
- 0 / 5
- Polubienia
- 30
- Pobrania
- 63
- Wydruki
- 0
- Wyświetlenia
- 806
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Computers
- Licencja
- Creative Commons — Attribution — Noncommercial
This is something I designed from scratch to use in a Sliger CX2177a case I used to build a server. This will allow you to mount a set of three 2.5" drives up to 15mm thick attached to the front fans on the case. If you are using an ATX motherboard, there is enough room for fans on both sides of the cage in this case. It should work fine with Sliger's other 2U models depending on the hardware you have installed. If you used a shorter depth 2U Sliger case, you would need to use a more compact motherboard to run these I believe. This will also work in other systems, but the added 2.5mm to the top and bottom may cause clearance issues.
With 15mm drives, these are pretty restrictive for airflow since they block over half of the airflow path. I found the Arctic P8 Max fans did a good job at a mid-range RPM setting. With my 2.5" SAS SSDs under load I was seeing 33-37 C temps with an ambient temp of 23 C. I have not tried U.2 drives, but if they run hot you may need more powerful fans. I ended up using the cage on one side and bars on the other for airflow reasons. The bars allow the fan to move more air for the peripherals beyond the cage. You can run bars on both sides but it will have a slightly unstable feel to it. Also you won't be forcing as much air through the drives.
Notes on the cage installation:
The height of this cage includes an additional 2.5mm above and below the fan due to the positioning of the fans in the case. Basically allows for the cage to rest on the case and take the strain off the fan from the weight of the drives. They have a top and bottom position, but are not side specific. The bottom of the cage is the part where the fan mounting screw holes are closer to the drive screw holes. To mount the drives, use a normal fine-thread screw like the ones used for CD drives. There is 3mm of plastic between the drive and where the top of the screw head sits.
Depending on how you want to mount the fan to the cage, the length of your mounting screw will vary. I designed this around M4 screws. Since the fan blocks the screws for the drives, there is an order to mounting the fans. After you assemble the first side you generally will want to attach the fan. If you mount the fan to the case using the normal coarse fan screws you will want a 20mm M4 screw to attach the first fan directly to the cage. To attach the fan and cage directly to the case, 45mm screws would be needed. If you want to attach a second fan to the other side of the cage 45mm screws work best for that as well.
I would recommend either straight or custom power cable for power. When it comes to data slim SATA or SAS cables are a must if you plan on doing more than one cage like I did in the Sliger CX2177a.
Installation guide video: https://youtu.be/R8Me8CIOmrk
Talking about my process I went through if you are interested: https://youtu.be/5C22zvqOqaU
eBay link to me selling the 13mm thick version of these: https://www.ebay.com/itm/226837637108
Dimensions: 88mm Wide 85mm Tall 10 or 13mm thick (Depends on the STL you choose)
Additional items needed: 20 or 45mm M4 screws (Depends on your mounting and fan plans.) M4 nylock nut (I recommend some sort of lock nut due to potential vibration issues over time) Fine thread SSD screws 80MM Fans
