1 / 2
4-Lane Pico MMU EBB42 PCB mount, cover and extension - Remix- Power and USB out the back — zdjęcie 1
1 / 2

4-Lane Pico MMU EBB42 PCB mount, cover and extension - Remix- Power and USB out the back

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Remix that puts the power and USB out the back side of the Pico MMU

Ocena
0 / 5
Polubienia
4
Pobrania
19
Wydruki
0
Wyświetlenia
164
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Accessories
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

What and Why?

This is a remix of @JesseCrash's PCB mount, PCB cover and mount extension to fill out the bottom of the Pico MMU.  I have my Pico MMU mounted at the top of my Ender 3 V3 SE, and ran into an issue with the PTFE tubes hitting and getting caught on the power and USB connectors when the head was at the top (z=230+) of the print area.

First of all, I couldn't have done it in anything like a reasonable amount of time if they hadn't included the .step files, so THANK YOU for that.  This required redoing all of the mount points for the EBB42 and rather than notch things for the rotated EBB42, I extended the depth of the PCB mount to accommodate substantial space under the PCB, as well as ensure enough space for the M3 threaded inserts.

Personally, I don't like things resting on the inserts themselves, so there is a "riser" above the insert.  You could trim things down a little, but I like the slightly thicker look as well.

The extension is just to make things look cleaner and fill in the gap between the stepper motor and the PCB Mount.

Printing & Post-Processing

  • Material: PLA

  • Layer Height: 0.2 mm

  • Infill: 15% (Gyroid)

  • Supports: You will need some kind of support for the PCB mount, the cover and the extension don't require any supports

  • Orientation: Print orientation is correct in the .stl files

  • Print Time: Mine printed in a little over 1:15

  • Post-Processing: Minimal cleanup needed on the back-side of the PCB mount where the supports were, where you install the heat-set inserts

Parts Needed

  • EBB42 board - Amazon, Aliexpress - Per the Pico MMU site, you don't need the one with the MAX31865

  • 5x M3 brass heat-set inserts (M3 x 4.6 x 3.8) - No links because you can make most any fit that are 4.4-4.6 OD fit as long as they aren't super long.  All but one of the inserts are put in through the back, so even if they stick out you should be fine if they are a tiny bit long.  The exception is the one in the top middle of the PCB mount for the cover screw.

  • M3 screws, you pick the cap end.  I believe I needed at least one 16mm, 2-3 10mm and an 8mm. (I'll update this once I get the time to take it apart again and measure the screws)

Assembly

You will need to remove two screws on the non-gear side A-tower that hold the tower to the rest of the Pico MMU assembly, the "front" top screw and the "rear" top screw (which also acts as the pivot for the lane zero feed gear.  As long as you aren't rough with it, it won't all come apart on you so pulling these both at the same time was fine for me, but they were out for 2 minutes and nothing got messed up.

Once the PCB Mount is mounted to the A-tower, mount the PCB with the top two screws.

Slide the extension in behind the PCB Mount and screw in the bottom left screw.

Finally, put the cover on and use the M3x16mm screw in the bottom right to hold the cover on as well as the screw in the upper middle portion of the cover

Notes

This was created with Fusion (Personal Edition) and while I do have the .f3d files...I'm embarrassed with how bad I am at optimizing the work flow so I'm not sharing those at this time.  I'm not opposed to it, I'm literally just embarrassed by them.  If enough people ask, I'll add those as well.

As a compromise, because I personally REALLY appreciate when a model designer includes something other than a mesh, I've included step files if you want to tinker.

Tagi