Ender 5 Pro Side Dual Z Mod Remixed and Top Filler for Mercury One Electronic Enclosure
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
This is a remix of Kornel052's work. Credit to his initial design. This remix addressed a few concerns raised.
- Ocena
- 5 / 5
- Polubienia
- 18
- Pobrania
- 49
- Wydruki
- 1
- Wyświetlenia
- 255
- Oceny
- 1
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Creality Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Noncommercial
This remix addressed the feedback from other users, as well as my own experience.
Increased the bed screw counter-sunk hole to 16mm to fit the silicon spacer. Steel spacer and spring spacer version available upon request.
Corrected the mounting holes of the top and bottom arm to M5 to correspond to the short extrusion's screw hole diameter from the original frame.
Amended the labelling of the arm to Front Right (FR), Rear Left (RL), Front Left (FL) and Rear Right (RR) of the bed adjustment screw. Abbreviations are engraved on the top side of parts for easy identification during assembly. This will prevent the bed screw misalignment issue caused by mixing up the screws. (All references made when looking at the front of the Ender 5 Pro, facing the toolhead or display)
Update 6 Apr 2026: Designed and uploaded alignment tools to aid installation. This is to prevent Z-axis binding, which can cause motor hang/skip or unsynchronised travel of both motors, leading to dire consequences.
For the user's convenience, I also uploaded the Z drop bracket from the Zero G team for the Mercury One Project. The actual file can also be found on their GitHub.
Update 5 May 2026: Bonus uploaded a new Y-axis limit-switch bracket to provide more rear travel. Useful for big toolhead.
Update 21 Aug 2026: Added Screw knob spacer. Noticed the screw are not aligned due to the wide recess underneath. Print the Screw knob spacer x 4.step and insert them to keep the adjusting screw aligned and straight.
Instructions for alignment tools:
Print both alignment tools for the top and bottom. The spacer can be reused for the top Z bracket alignment.
The shorter spacer is to be placed in the front. Longer is for the Rear. This gives the front linear rod 90cm offset (from the centre of the rod) to the front 20x40mm extrusion. The back linear rod is placed 110cm away from the back extrusion.
Install the front spacer, seating it tightly against the front 20x40 extrusions, and secure the M3 bolt with a t-nut by hand. No need for tools, as we don't need it super tight.
Install the original linear rod bracket and stepper motor bracket. Keep the bolts loose for adjustment.
Drop in the linear rod to act as a guide for the alignment tools. Let it rest on the table or floor, wherever you are working.
Install the stepper motor without the coupling onto the bracket. Secure only the 2 screws nearest the centre of the printer. The back screw will hinder the bracket from seating firmly and flat. The motor's 5mm shaft will be aligned with the tool.
Install the bottom rail guide alignment tool. Secure the alignment tool with 2 x M3 bolts and a t-nut. Ensure the alignment tool is seated firmly against the front spacer and flat on the extrusion.
Move the bottom linear rod bracket to align the rod with the alignment tool.
Tighten to secure the motor bracket from the centre access cutout of the alignment tool. Make sure it will not move anymore. Do not over-tighten and damage the bolt or your allen key
Tighten to secure the Z bracket firmly.
Now repeat the process for the top linear rod bracket, but use the spacer with the flat side against the aluminium extrusion, as there's an L bracket in the way on top.
In the pipeline
Mercury One Electronic enclosure's top filler to accommodate this side dual-z setup, so the top acrylic panel fits.
Update 6 Apr 2026: Work in progress; awaiting completion for photo illustration prior to uploading. Will also provide .dxf file for the top Polycarbonate panel.
Update 25 Apr 2026: Uploaded the DXF file for the electronic enclosure top panel. Test fitted to be a perfect fit.
Update 5 May 2026: Released the top filler of the electronic enclosure that supports the top panel. The rest of the fittings are on Mercury One's page for the electronic enclosure or in the official CAD file.
Precise Alignment Tool for the bottom motor and rail bracket.
Update 6 Apr 2026: Alignment tools have been uploaded. Both Z rails are well aligned and have smooth travel on the first attempt.
Stress-test the process G-code to ensure the dual Z-axis is not slipping due to misalignment.
Update 6 Apr 2026: Decided no need to publish as the alignment tool does a great job. Also, the G-code is specific to either Klipper or Marlin and not universal.
Possible shifting of the linear rod outwards to be within (align with) the top and bottom extrusions. This is done by extending the linear rod's arm.
Print with:
0.2mm layer height, first layer 0.25mm
Line width 0.4mm for all
Minimum 4 walls, both horizontal (Top & Bottom) and vertical. Recommended 5 walls for all settings
Infill 40% Gyroid due to the structural part and to support the heavy bed
Grid support for the large counter-sunk bore of the silicon spacer
PETG-CF for rigidity and higher temp tolerance due to radiating heat from the bed. Ideally, use PA-CF. If enclosed, minimally print with ABS or PA-CF
Wall Printing Order (Inner/Outer) for strength
Support
If you like this, consider buying me a cup of coffee. Thank you!
