1 / 13
Samsung S23 Ultra Multi-Stage Lens Hood Kit — zdjęcie 1
1 / 13

Samsung S23 Ultra Multi-Stage Lens Hood Kit

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

These lens hoods keep even more stray light out of your lens, increasing contrast and preventing blown out pics.

Ocena
0 / 5
Polubienia
5
Pobrania
52
Wydruki
0
Wyświetlenia
719
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution

Introduction

As awesome as the 10x telephoto lens is on the S23 Ultra, I noticed that in non-ideal lighting conditions (or if your lens is damaged or smudged), captured images could sometimes look blown out with poor contrast.  I made a few different-sized lens hoods and this is what I came up with for maximum glare removal.

The design files themselves have been made available in .f3d, .ipt, and .step files.  In Fusion 360, the parts are somewhat parametrically designed, allowing changes to adapt to other phones in the future to be less of a headache.

If you are sufficiently happy with how this design has worked out for you or you have had success with commercially selling these, please consider sending a donation my way if you are able: https://buy.stripe.com/bIY4i488N84rcCY3cc 

Notable Printing Considerations

  • Make sure to print this part out of a black coloured filament.  Otherwise, you will not be removing as much glare.

  • To print these lens hoods at a fine enough detail, a 0.25mm nozzle and layer heights as low as 0.06mm are recommended.  The low 0.06mm layer height is needed on the 1x zoom lens hood for a 15º overhang without using support material, otherwise a 0.1mm layer height should be adequate.  Use a variable layer height to keep print times from being abysmal, as demonstrated in the 1x lens hood .3mf file.

Notable Post-Processing Considerations

  • Print defects can impact image quality.  Shine a light through the ends of the light hoods after printing and ensure there aren't any defects or stringing(especially when printing in PETG).  A heat gun or hair dryer can be useful for collapsing any stringing inside that you can't reach, as long as you are careful not to melt the part.

  • These lens hoods are friction fit to the camera lenses on the phone.  They will need a very small amount of sanding or use of a rotary tool to get the fitment to your liking.  Without any sanding or grinding, the lens hoods will likely be very difficult or impossible to install and remove.  In the image below, edges marked in red should require some light sanding or grinding.  Yellow edges shouldn't require any, but print defects from support material could be present here and require removal.

Multi-Stage Lens Hood Design

Our 3D printers can't print a black surface that absorbs 99.9% of light that hits it like a professional lens hood, but it can print a black surface that absorbs well over 90% of the light that hits it.  By using a multi-stage design, stray light can be forced to reflect off the lens hood internal surfaces many more times before eventually hitting the sensor, or even reflect the light back out entirely. 

A diagram is shown below with the red lines showing how light might reflect in a more normal lens hood design, while the other line colours show where the light might internally reflect in the multi-stage lens hood design.

Comparisons

The multi-stage lens hoods are most noticeable on the 10x lens, but there is still a difference on the 3x and even 1x lenses.  Below are some examples of the 10x lens and the 1x lens.  The lighting environments of the pictures are worse than normal scenarios to showcase the lens hood effects, but are by no means outside of what kind of lighting environment you may be subject to.  The camera lenses are clean in all pictures.

*****CLICK ON THE IMAGES TO SEE HIGHER IMAGE QUALITY*****

Comparison of Image Quality - Stock Android Camera App in Pro Mode (Identical Exposure Settings)

Android Camera App no Lens Hood - 10x Lens 1/50 sec ISO 200

Android Camera App with Multi-Stage Lens Hood - 10x Lens 1/50 sec ISO 200

Android Camera App no Lens Hood - 1x Lens 1/1600 sec ISO 50

Android Camera App with Multi-Stage Lens Hood - 1x Lens 1/1600 sec ISO 50

Android Camera App no Lens Hood - 10x Lens 1/320 sec ISO 50

Android Camera App with Multi-Stage Lens Hood - 10x Lens 1/320 sec ISO 50

Comparison of Image Quality - Stock Android Camera App in Pro Mode (Optimal Exposure Settings)

Android Camera App no Lens Hood - 10x Lens 1/30 sec ISO 125

Android Camera App with Multi-Stage Lens Hood - 10x Lens 1/30 sec ISO 200

Comparison of Image Quality - ExpertRAW Camera App

ExpertRAW no Lens Hood - 10x Lens 1/60 sec ISO 200

ExpertRAW with Multi-Stage Lens Hood - 10x Lens 1/60 sec ISO 320

ExpertRAW no Lens Hood - 10x Lens 1/320 sec ISO 50

ExpertRAW with Multi-Stage Lens Hood - 10x Lens 1/320 sec ISO 50

Tagi