FS2026: Bi-directional Eco Remix with Original Lid
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A support frame to allow using the FS2026 system with the original lid without going upside-down.
- Ocena
- 0 / 5
- Polubienia
- 15
- Pobrania
- 52
- Wydruki
- 0
- Wyświetlenia
- 786
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Accessories
- Licencja
- GNU General Public License v2.0
Premise
The idea behind this whole endeavor was to use the new FS2026 system without having to waste filament on printing an entirely new lid or having to drill a hole into the box, and consequently being able to use the box in its correct orientation. Luckily someone already adapted the side pieces holding the rewinder to fit the old remixed FS2025 lid frame, but I still had to come up with a support structure to prevent everything from sliding downward, and the frame was still blocking the opening of the original lid to some degree, preventing the use of one of the many lid cap designs available.
While working on this, I also noticed something about the clutch: The design of the clutch does not suck, you are just missing critical information. Turns out using the same material for both the clutch and the slip disc is a really bad idea, as it maximizes the so-called stick–slip phenomenon - the assembly sticks until it doesn't, and then refuses to stick until it released most if not all of the tension, which is not what you want from a clutch. Using a TPU clutch on an ASA slip disc works surprisingly well and will only release a tiny bit of tension each time, but if you want the clutch to slip as smooth as possible I can recommend investing into a roll of SEBS from Recreus, its silky high-friction surface works with very little pressure and slips almost yank-free while still maintaining max torque. As it turns out the springs are only capable to turn so much before they will simply stop, tightening the dial further will just increase the torque required to start slipping without gaining any more rotation, and with SEBS I still managed to get as much rotation out of it as possible, with TPU being a fairly close 2nd place.
If it wasn't obvious already, this was designed for the popular 4l cereal boxes with a hexagon on the lid.
Requirements
The following other parts are required for a full assembly:
FS2025 Remix Base for Lid Caps with Larger Desiccant Box to free up the original lid opening
FS2026 Rewinder adapter for 2025 Official Remix Base by @Pixel_Crafts to mount the rewinder onto the above remix of the old base frame
The original FS2026 rewinder assembly by @GunplaMark - in my case the original axle was fitting tight enough in PETG to remain in place, but I still recommend to use a lengthened one (e.g. the one provided by me here), especially if you're printing with more precise materials like a well-tuned ASA profile.
Recommended additions
The following other pieces are not strictly needed but a recommended addition, all of them are visible in the pic:
Cereal Drybox Cap with integrated dust filter (hexagon variant)
Coupler Cap + Adaptor for Ultimate Filament Drybox by @PhilCaruso
Setup
The heart of this remix is the support structure consisting out of a frame sitting at the bottom of the box and two pieces of vertical struts to provide the necessary support for the lid frame. The piece with the single strut needs a bit of support to get around the little bulge at the bottom of the cereal box, the rest prints without supports.
I originally intended to have them snap into each other like the lid frame and side pieces, but FreeCAD kept wrecking my file at some point (the update to 1.1 even broke the previously working file I exported these files from) and in order to get everything to fit properly with the countless odd angles n' stuff I already wasted more than enough filament prototyping the whole thing, so you will have to bear with having to glue these pieces together - it's not strictly necessary, but it will save you a lot of fiddling while using the whole thing. Use a type of glue that gives you at least a little bit of time for corrections. Glue the three pieces together, put them into the box, put the frame on top and close the lid to wedge everything in place and let it cure like that - you can open the cap to allow the fumes to escape. Don't worry about the box - it's made of PP, nothing will stick to it.
There are two remixes of the original FS2026 system here:
Closed clip. The original clips can be very loose (and break easily) when the clip and axle are printed with a well-calibrated ASA or PLA profile, which is an issue if the bearing at the nut keeps slipping off the axle when handling the final assembly outside of the box thanks to the weight of the spool - this is easily fixed by printing this closed "clip" in stiff TPU instead. If the tension is not enough, just put it on upside-down for even more tension.
A lengthened axle. The axle slipping out of the side parts holding it in place is a known problem, this is just another attempt to fix it. However, it is specifically designed to precisely stick out of the side supports to use the above closed clips as an additional fixation at the tips of the axle to keep everything in place without putting too much tension on the sides of the box - as such it only provides 2mm extra on the hub side and 1.5mm on the nut side.
By the way, as someone was already complaining about FS2026 needing too much space on the build plate: This entire assembly prints with a 220mm build plate without having to orient parts diagonally!