1 / 4
Garmin bike mount— QuickFit (22mm and 26mm) — zdjęcie 1
1 / 4

Garmin bike mount— QuickFit (22mm and 26mm)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Super QUICK and SIMPLE bike mount for your garmin watch. So you dont need to buy a pricey bike computer :)

Ocena
0 / 5
Polubienia
3
Wydruki
0
Wyświetlenia
691
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Standard Digital File License

Turn your Garmin watch into a cycling computer in seconds.

I designed this mount because I was tired of my watch shaking on my wrist every time the road/trail got rough. After 10+ prototypes, many FEA simulations, and hundreds of miles of testing with my local cycling group, I’ve refined this into what I believe is the perfect solution for mounting your Garmin watch on your bike.

Whether you're a triathlete looking for a quicker transition, a roadie who wants an unobstructed view of your stats, or a trail rider needing a rock-solid display that won't budge on technical descents, this mount delivers a secure connection between your watch and your bike.

Why This Design?

  • Rock-Solid Mounting: Designed with tight tolerances to ensure a "click" feel and very secure fit  (I did about 5 prototypes to perfect the click)

  • Low Profile & Lightweight: Minimalist aesthetic for clean cockpit a super low-profile for those aero gains! Only 4.55g when printed with 15% infill as recommended

  • Watch-Safe Geometry: Smooth contact points to ensure watch pins aren't stressed during use.

  • Dual-Security Attachment: Most mounts rely on one thing. This design utilizes a "Hybrid-Fix" system—double-sided tape to stop rotation and vibrations and dual Zip-Ties for mechanical locking. It’s not going anywhere!

Recommended Print Settings

For a part like this that will be exposed to sun and under tension, material matter! 

Setting

Recommendation

Material

PC (Prusament PC Blend), PETG, or Nylon (for UV resistance & flex)                                       PLA can be used, but i generaly do not recommend it because it can sag over time.

Perimeters

2 Walls

Infill

15% Gyroid (I print it like this, but if you want you can use 100% infill)

Layer Height

0.15mm or 0.2mm (for smooth click)

Supports

Not needed, print on side (it should import this way in the slicer)

Brim

Not needed, although the slicer recommends adding brim and supports, you can ignore this warning.

Compatibility

  • Watch Side: Designed for Garmin watches using standard 22mm or 26mm QuickFit pins (if you wish for compatibility with any other watch or modification like handelbar mounting, comment and I can make a special version).

  • Bike Side: Fits most standard bicycle stems (modification on request in comments). The curved base is designed to "hug" the stem.


Installation

To ensure the mount never rotates—even on the gnarliest trails—I designed it to be installed using a two-stage process.

  1. Prep the Stem: Clean your stem with a bit of isopropyl alcohol to remove any grease.

  2. Stage 1 (Adhesion): Apply a small piece of strong double-sided mounting tape (like 3M VHB) to the underside of the mount. Then press the mount firmly onto the center of your stem.

  3. Stage 2 (Mechanical): Thread two mini zip ties (2.5x1mm) ,through the integrated slots and cinch them down tight. The tape prevents "sliding," while the zip ties prevent "lifting."

  4. Click & Ride: Snap your watch (strap removed) into the mount. You're ready to go! When you are done with riding, just press the tab on the mount and the watch pops out.

Tagi