Cable Spool Holder Gridfinity - M3 Heat Inserts, Label, Press Fit Magnets, Thin/Wide Clamps, Cable Start Pinch (Source included)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Quality of Life Upgrades for the awesome Cable Spool Holder from firstgizmo!
- Ocena
- 5 / 5
- Polubienia
- 25
- Pobrania
- 105
- Wydruki
- 0
- Wyświetlenia
- 477
- Oceny
- 1
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Organizers
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Combination of several remixes made of the awesome Cable Spool Holder Gridfinity of @firstgizmo into one model. Plus some quality of life updates and fixes.
Also STEP and Fusion 360 sources are included to make it easy for everyone to adjust the model to their needs.
Features
M3 heat inserts like @Reddi and @CerialPhreak
Label holder like @Vodzurk
Double sided clamp for thin wires like @bodja and @earlmckay
Double sided clamp for thicker wires like @Thorou and @codysechelski
Pinch where the cable starts that align with the spools wall
Press fit 6x2mm magnet holes (⌀ 6.1mm)
Removed one tooth from crank tools so they don't interfere with the cable start
All clamps have been remodeled since there were some strange artifacts (nothing that impacts functionality of the original model).
Clamps and Cable Sizes
Clamp Type | ⌀ Min | ⌀ Max | AWG Min | AWG Max | Metric Min | Metric Max |
|---|---|---|---|---|---|---|
Clamp Single | 0.156mm | 2.6mm | AWG36 | AWG15 | 0.01mm² | 1mm² |
Clamp Double Thin | 0.113mm | 1.3mm | AWG38 | AWG26 | 0.005mm² | 0.14mm² |
Clamp Double Wide | 1.0mm | 2.4mm | AWG24 | AWG16 | 0.22mm² | 1mm² |
Bill of Material
Part | Count | Comment |
|---|---|---|
Base Plate | 1 | |
Corner | 1 | |
Side Plate | 2 | Use SidePlate_x2 from @firstgizmo |
M3 Heat Inserts | 8 | e.g. from Ruthex |
M3x10 FHCS | 8 | ISO-10642, 8mm to 16mm |
6x2mm Magnets | 8 | e.g. from Amazon |
Choose one Clamp⬇ | ||
Clamp Single | 1 | |
Clamp Double Thin | ||
Clamp Double Wide | ||
For Spool 1x Hex Key Left | ||
Spool 1x Counter | 1 | Use Spool_B from @firstgizmo |
Spool 1x Key (left) | 1 | |
For Spool 1x Hex Key Right | ||
Spool 1x Counter | 1 | Use Spool_B from @firstgizmo |
Spool 1x Key (right) | 1 | |
For Spool 0.5x | ||
Spool 0.5x Counter | 2 | Use SpoolSmal_B from @firstgizmo |
Spool 0.5x Key (left) | 1 | |
Spool 0.5x Key (right) | 1 | |
For Manual Crank Tool | ||
Hand Crank | 1 | |
For Power Crank Tool | ||
Power Crank | 1 | |
Power Crank Shaft | 1 | Use Tool_B from @firstgizmo |
Printing and Assembly
@firstgizmo did an amazing job describing printing and assembling the cable spool holder on the original model. No changes using this models. But leave him a ❤ while you there.