1 / 4
LEGO Saturn V - LED Launch Stand (Freestanding & IKEA Blåliden) — zdjęcie 1
1 / 4

LEGO Saturn V - LED Launch Stand (Freestanding & IKEA Blåliden)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Orientacyjna cena wydruku pliku

1,08 € – 1,32 € netto (bez VAT)

Dla pliku: LegoSaturnV_IKEABlaliden_OnlyTop_0.4n_0.2mm_PLA_COREONE_41m.bgcode

To wstępna wycena jednego pliku. Dokładną cenę poznasz przed zamówieniem.

Plik i założenia wyceny

Plik użyty do wyceny

Średnia wycena orientacyjna: 1,20 € netto (środek widełek).

Masa podana przez autora
26 g
Czas druku podany przez autora
40,8 min
Materiał u źródła
PLA
Materiał wyceny
PLA
Drukarka wyceny
Bambu Lab P1S - 0.4 nozzle
Proces wyceny
0.20mm Standard

Orientacyjna wycena wyłącznie wybranego pliku, oparta na masie i czasie druku podanych przez autora. Warianty plików nie są sumowane. Ostateczna cena zostanie obliczona po analizie pliku.

Zapisane na tym urządzeniu.

Parametric 3-part LEGO Saturn V LED launch stand. Uses cotton & LEDs for fiery exhaust. Freestanding or IKEA Blåliden.

Ocena
0 / 5
Polubienia
2
Pobrania
11
Wydruki
0
Wyświetlenia
124
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial

A parametric display stand for the LEGO Saturn V that simulates a fiery engine ignition.

This 3-part stand uses a standard flexible LED strip and cotton wool to create a glowing smoke/fire effect while keeping the electronics safely separated from the cotton. It includes options for freestanding display or fitting inside an IKEA Blåliden cabinet. Parametric FreeCAD model included.

Design (3 Parts) and File Setup

  • Inner Cylinder LegoSaturnV_InnerCylinder.3mf: Wrap your flexible LED strip around this core.

  • Outer Honeycomb Cylinder LegoSaturnV_OuterCylinder.3mf: Diffuses the light and acts as a safe barrier for the cotton wool.

  • Top Plates (Choose One):

    • Freestanding LegoSaturnV_Top_Freestanding.3mf: A wider plate to directly support the rocket on any surface.

    • IKEA Blåliden LegoSaturnV_Top_IKEABlaliden.3mf: A compact cap that secures the cylinders under the cabinet's glass shelf (the rocket rests directly on the glass).

  • Source Files: The fully parametric FreeCAD (.FCStd) file is included for easy modification.

Build

Print

I printed with PLA+ on standard settings with reduced infill (10%).

Hardware Required

  • Standard flexible multicolor LED strip

  • Cotton wool for the smoke/fire effect

Build Instructions

  1. Print: Print your three chosen components (Inner, Honeycomb, and the Top Plate you need).

  2. Wrap LEDs: Peel the backing off your LED strip and wrap it tightly around the Inner Cylinder. You can fixate the start of the strip at the top or use it as an outlet. Route the power cable out through the bottom.

  3. Slide the Outer Honeycomb Cylinder over the Inner Cylinder

  4. Snap or press the Top Plate onto the assembly to lock both cylinders in place.

  5. Add Smoke: Gently pull apart and fluff your cotton wool. Wrap and optionally glue/tuck it (I didn't need to) around the outside of the honeycomb cylinder to simulate launch smoke.

  6. Place your LEGO Saturn V on the stand, plug in the LEDs, and ignite! For the IKEA version, the height of the overall construct allows putting the rocket on a glass shelf above it to improve its stability.

The concept was inspired by the brilliant diorama created by @0d7i0s_467 here: https://www.printables.com/model/18143-lego-saturn-v-diorama

Tagi