1 / 3
Garmin Quarter Turn Mount for 24mm bike handlebars — zdjęcie 1
1 / 3

Garmin Quarter Turn Mount for 24mm bike handlebars

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Garmin quarter-turn mount for 24mm bike bars. Assembly-in-print technique, no supports. PETG recommended.

Ocena
0 / 5
Polubienia
1
Pobrania
26
Wydruki
0
Wyświetlenia
129
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Garmin Quarter-Turn Mount for 24mm Handlebars

A ready-to-use Garmin quarter-turn interface mount designed to fit 24mm bicycle handlebars. This is a remix of my original model, which serves as a design template demonstrating the pause & assembly-in-print technique. With this remix, I've turned that template into a functional, printable mount you can actually put on your bike.

Remix of: 


Print Settings

Setting

Value

Material

PETG

Nozzle

0.6 mm

Layer Height

0.15 mm

Walls

3

Supports

None – do NOT use supports!

⚠ Important: No Supports!

This model uses a pause & assembly-in-print technique. If your slicer suggests supports, disable them. Supports will interfere with the print process and break the assembly.


Skill Level

Intermediate / Advanced – This print requires a pause-and-resume workflow where you insert a previously printed part into the running print. If you're unfamiliar with this technique, please refer to the detailed instructions in my original model (linked above) before starting.


Hardware Required (M3)

  • 2× M3×25 flathead screws

  • 2× M3 nuts (DIN 934)

  • 2× M3 washers

  • 2× M3 spring lock washers (DIN 127)

  • A small piece of old bicycle inner tube (for anti-slip grip on the handlebar)


Printing Process

This model consists of three parts: the housing (main clamp body), the bracket (counterpart), and a spring (a small tension element that keeps your Garmin device locked into the quarter-turn interface).

Print Order
  1. Print the spring first. This is a separate, small print.

  2. Print the housing and bracket together in a single print. During the housing print, you will need to pause the printer and insert the previously printed spring into the housing before resuming. This is the assembly-in-print step.

For detailed instructions on how the pause & insert technique works, please refer to my original model (linked in Credits).

⚠ Print Orientation Matters

Please check the included screenshot for correct print orientation. Printing the bracket flat on the build plate ensures the layer lines run in a direction that maximizes bending strength – important since the bracket is under constant load when clamped to the handlebar.


Assembly

1. Post-Processing

The screw holes are designed as blind holes – thin layers of material seal the bottom of each M3 hole. Before assembly, push through these layers using one of the M3 screws. This opens up the holes for mounting.

Then, press the two M3 nuts (DIN 934) into their designated pockets in the housing. They should fit snugly in place.

2. Mounting on the Handlebar
  1. Cut a small strip of old bike inner tube and wrap it around your handlebar at the mounting position. This acts as anti-slip padding and prevents the mount from shifting.

  2. Place the mount onto the handlebar over the rubber strip.

  3. For each of the two mounting bolts, stack them in this order: flathead screw → spring lock washer → washer → (through the mount and bar clamp) → nut (DIN 934).

  4. Tighten both screws evenly. The spring lock washers will help keep everything secure under road vibration.


Credits

This is a remix of a remix:

  1. 👉 Original design: 

    The original Garmin quarter-turn mount template that started it all.

  2. 👉 My first remix (assembly-in-print template): 

    I remixed the original into a design template showcasing the pause & assembly-in-print technique – aimed at other designers.

  3. This model takes it the final step: a ready-to-print, functional mount for 24mm handlebars.

The assembly-in-print template (link 2) contains detailed instructions for the pause & insert technique used in this print. Please check it out if this is your first time using this method.

Tagi