1 / 6
Airsoft STANAG-style Magazine (30 rounds, rear-fed) — zdjęcie 1
1 / 6

Airsoft STANAG-style Magazine (30 rounds, rear-fed)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Airsoft STANAG-style magazine with a capacity of 30 6mm BBs. Note that this design is rear-feeding.

Ocena
0 / 5
Polubienia
2
Pobrania
64
Wydruki
0
Wyświetlenia
332
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Other Sports
Licencja
Creative Commons — Attribution — Share Alike

I have an old no-name M4-style softgun which uses non-standard rear-feeding STANAG-style magazines, which are very hard to obtain today.

As some of the interal parts of my original magazine has cracked over time, I decided to reverse-engineer it so it is 3D-printable and compatible with the hardware of the orignal magazine (compatible non-printable parts can be seen in in the LoM below.

The biggest differences between this variant and the original:

  • Easier to 3D print

  • Improved alignment pins

  • Jam-resistant follower (bigger, longer legs that have more traversal margin)

  • Made the stopper be more reliable (blocks more of the BBs in its neutral position, reducing the chance of a BB slipping past it)

  • No weight slot. The original has a piece of steel inside it to add weight, but I left this out of this variant.

  • Added a capacity limiter. The follower allows space for 30 6mm BBs in the feed channel until it hits the capacity limiter. This also protects the follower spring from being over-compressed, which can lead to plastic deformation of the spring, or potentially it shooting out of the magazine if the follower spring retention plate would give way

I have printed, assembled and tested up to V2 of the parts as of yet, the results of which lead to the untested improvements of the V3 magazine halves.

List of Materials

  • 1× Compression spring, feeding follower, approx. 5.6 mm OD × 500 mm L

  • 1× Compression spring, BB stopper / gate, approx. 3.8 mm OD × 17 mm L

  • 4× Pan-head self-tapping screw, approx. 2.2–2.6 mm dia × 9–9.5 mm L

Here's the Onshape link if anyone wants to do further inspections or tinkering. I noticed the exported STEP file has some issues.

Print Settings

  • Layer Height

    • Anything works as long as there's good layer adhesion

  • Perimeters

    • 4-6 perimeters

    • 4-6 layers on top and bottom

  • Infill

    • Internal components: 85-100% grid

    • Magazine halves: 15-50% grid

      • 15% works fine with 6 perimeters. Add infill primarily to add weight and neglible rigidity

  • Brim

    • 2-3mm outer brim

      • You may or may not need this for the magazine halves if you have good bed adhesion

  • Supports

    • See blue areas on the slicer screenshot

      • Left half has the mag retention slot, which is the rectangular cutout. Both this and the outer edge should be supported

      • Right half does not have the magazine retention slot. Only the outer edge is needed

  • Material

    • PETG is easy to print and impact resistant enough for this. ASA is also a good option, but not tested.

    • PLA is not recommended, but can be used only if this is meant to be used as a decoration or for in-door use only. 

Assembly Instructions

YouTube Assembly Video (Version 1 parts)

  1. Remove any brim, skirt and supports from the parts, specifically the spring retention pin.

  2. Place one magazine half down, and insert the following components:

    1. BB Follower: insert it into the BB channel, with the rounded end pointing towards the feed opening of the magazine (the big round opening). Make sure not to place it between the capacity limiter (the perpendicular piece to the follower rail) and the retention spring opening (the rectangular opening)

    2. BB Stopper/Gate & Small Spring: Insert it into the gate slot at the top of the magazine, making sure the orientation is the same as in the pictures. Wedge its spring around its pin, and brace it to the wall on the other side of the gate slot. The gate opening should partially block the BB channel in its neutral state.

  3. Carefully position the other half of the magazine on top, using the 6 alignment pins. Make sure the gate spring remains in its place during this step.
    Press the halves firmly together so each half is flush to the other.

  4. Insert 1x screw into the screw hole which is the furthest away from the retention spring opening. Tighten it as you normally would.
    This step helps keeping the halves together for the next step.

  5. Insert the follower spring through the rectangular opening. If the BB follower can be seen getting pushed into the BB gate opening, you know you are doing it correctly. If not, re-open the magazine and properly insert the BB follower.

  6. Keep pushing the spring all the way into the magazine. The last 3rd of the spring should be somewhat tricky to insert, but this just means the spring has a proper compression strength.

  7. Once the spring is fully inserted, take the retention pin and insert the rod into the spring. Carefully pry the halves apart just enough for you to be able to install the retention pin properly, then press the halves firmly together and install the remaining 3x screws.

Assembly Tests and Notes
  • The backplate of the retention spring should sit flush with the top of the magazine, as seen in the picture (blue part).

  • The BB gate/stopper (yellow part) should be movable in and out of the magazine. It should also stop inserted BBs from flying out as long as it is in its neutral position.

  • The BB follower should slide nicely along the channel rail, and should be pushed by the follower spring all the way to the BB stopper/gate with some force.

  • If the single screw from assembly step 4 is unable to keep the halves together properly, try partially installing more screws or clamping the halves together somewhat.

  • The BB follower has relatively tight margins to the channel, and it may end up slightly oversized depending on the printer settings. If it has issues sliding through the entire channel, simply file it down somewhat on the sides. The legs may end up thinner than normal, but this is fine as their primary function is to prevent the follower from rotating and jamming inside the channel.

  • Should there be issues with the BB gate not opening smoothly when inserting the magazine, try sanding down the wedge part somewhat, as layer lines may prevent it from having a smooth operation.

Updates

  • Update 23 April 2026

    • Increased feeding rail tolerance

    • Added draft to magazine retention slot to compensate for tight tolerances

    • Made feeder spring easier to insert

    • Strengthened mounting points (both alignment pins and screw mounts)

    • Increased magazine retention slot wall thickness

    • Added chamfer to alignment pins and screw mounts, making them easier to align

    • Added gate spring mount notch, so it doesn't slip out as easily during assembly, keeping it centered

  • Update 22 April 2026

    • Added supports to the spring retention pin for more reliable printing, as printing this part vertically is not recommended due to strength requirements of the part. These supports enable effortless horizontal printing without relying on decent slicer supports.

    • Improved feeder tolerance and overhang printing.

    • Improved feeding opening overhang printing.

    • Fixed the chamfer of one of the screw openings.

    • Added G-Code for printing statistics overview.

  • Update 17 April 2026

    • Revised the BB stopper/gate to have a more aggressive actuation angle, as it could prevent the magazine from being inserted properly in some situations depending on layer height and width used when printing.

Tagi